Finn Lassen wrote:
Someone told me one can get a chemical kit to test for exhaust
gasses in the
coolant.
I've checked in local stores with no luck. What is it called?
And
where can I
get it?
I'm loosing coolant. Tracy and others have suggested that it may
be
a failing
combustion chamber/coolant jacket o-ring - the combustion gasses
pressurizing
the coolant.
Before I take the engine apart, I want to be sure that that
really
is the case.
Finn
Finn how large is your overflow can? Last time I saw your can
(Oct.)
it looked too small.
What happens is the coolant expands when heated and flows out to
the
overflow can.
This is normal. If the overflow can is too small some is forced
out of
the overflow can each time you fly the airplane. When the engine
cools
off
what is in the can is normally sucked back into the engine. If not
enough is in the
can, air will be sucked back into the engine which is a big no no.
I suspect about a gallon can is needed. Make sure the over flow
tube
goes
to the bottom of the can. Try that first.
Paul Lamar
I didn't use to have the problem. I'm now loosing up to 2 quarts per
hour (depending on
power/RPM). Looks like the problem is gradually getting worse.
I replaced the cap and am thinking about going to a higher than 16
psi
cap, but again I
didn't use to loose that much coolant.
So, what is that kit called? What do I ask for?
Finn
Are you sure you are getting all the air out of the engine when you
fill
the system. Are you raising the tail when you fill it? Do you have a
vent line from the front (rear in the car) of the engine back to the
pressure cap area?
Well there are some rad pressure check kits. A cold pressure check
around
30 psi should show it up real fast. We could not find a kit in Palm
Springs
so I made one for Perry's engine out of a tubeless tire schrader
valve and a pieces of aluminum plate. A lot of external leaks won't
show up on the ground. You need to warm up the engine and have
pressure
in the cooling system before they start leaking.
If you can't find any external leaks it could be an O-ring internal
leak.
Has the engine been overheated? Could be a broken O-ring land heaven
forbid.
What year is that engine? Also inspect your engine tension bolts to
make
sure none are fractured. That is what caused Perry's internal leak.
I'll wager they were never taken out one at a time and coated with
red RTV and replaced. Were they? :-)>
Paul Lamar
I think Finn has tried all the simple stuff. His problem seems to be a
little stickier. The system seems to hold static pressure just fine but
starts overflowing at high power settings (but not necessarily
overheated).
I guessed that there may be an O-ring leak in the high pressure portion
of
the combustion chamber that only leaks at peak combustion chamber
pressures.
Just a guess but it fits the symptoms.
Tracy Crook
tcrook@rotaryaviation.com
www.rotaryaviation.com
Finn,
Snap - On Tools sells two different test kits for this purpose. As I
understand it they both resemble a turkey baster with a couple of chambers
in it, in which you put in a test chemical and test through your rad cap
hole. If the chemical changes colour you have gasses present. If there is no
change in colour then no gases and you can reuse the chemicals later for
another test. The more expensive one is supposed to be more accurate. Part
number YA2000 is $80.75 and comes with 100 cc of chemical and a further 500
cc is available for $21.00 ( don't know the part number ). Part number
GA170B is $61.45 and the refill is $9.70 for 16 fl oz. The best part is that
these are the Canadian prices.
Hope this is what you were after.
John Gibbons
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org