OK back from Florida, Shady Bend and Tracy's cooling test.
I am here to say that the difficulty of cooling a Mazda rotary engine
in an airplane has been greatly exaggerated. Its a myth for sure.
People are not paying enough attention to getting the air out of the
cowl. Making the inlets larger and larger will do absolutely no good
at all unless the outlets have two or three times more area than the
inlets. All you would be doing is adding drag.
In effect Tracy has been cooling his engine with only one of his two
radiators for the past five years despite a huge inlet on the right
side of his cowl.
Here is the last set of several sets of pressure data we measured on
his cooling set up. The hole behind the prop spinner was taped up in
an attempt to seal it. This made the pressure in the cowl about a 1/2
inch of water higher pressure confirming what Jim Mosure discovered.
Apparently the spinner backing plate and prop bolts and nuts are
function somewhat like a centrifugal pump lowering the pressure in the
cowl.
All numbers are in inches of water at 120 MPH
Front of oil radiator _______________6.36
Front of right radiator _____________5.11
Front of left radiator ______________8.36
In cowl behind radiators ____________3.61
Under fuselage behind cowl opening __0.86
The dynamic pressure at this 120 MPH speed is 7.6 inches of water. The
slip stream from the prop is increasing the pressure in front of the
left radiator apparently.
As you can see the pressure difference across the right radiator
is 5.11 - 3.61 is only 1.5 inches of water or about .055 psi
which is hardly enough to generate a gentle evening breeze.
In effect this radiator is not functioning. Well hardly at all.
In general the cowl pressure is much higher than it need be
judging by the near ambient pressure under the fuselage near
the cowl outlet opening. Tracy's airplane is in dire need
of a cowl flap down there. If Tracy installed a proper cowl
flap the engine would cool much better and probably with
smaller water radiators and cowl openings.
In the picture of the left cowl opening below one can clearly
see the static pressure tap using porous kitchen foam hot glued to the
end of the drip irrigation tubing.
For more pictures on the test see Tracy web site at:
http://www.rotaryaviation.com/
click on "What's new at RWS cooling Test."
Paul Lamar
________________________________________________________________________
_____________
Paul, Tracy and Group,
The cowl pressure could probably be lowered by a vent / louver on the
top-front of the cowl right behind the spinner. The pressure graphs
that I have seen of the RV-6 show that the area of the prop spinner and
the very front of the cowl as low pressure areas - this probably isn't
always true but would seem to be on Tracy's airplane. I think that this
is why the cowl pressure (inside the cowl) rose when the cowl opening
behind the spinner was closed - this low pressure area was no longer
used to evacuate the air inside the cowl. A side benefit would be the
hot air inside of the cowl would have an exit vent (especially on tail
draggers) after the flight was complete. This would help cool down the
inside of the cowl after shutdown.
Ken Powell
Guys I think just about everybody is missing the point of a cowl flap.
A cowl flap is a variable nozzle device. You DON'T WANT a lot of opening
at high speeds. You WANT TO SQUIRT that hot air out the back at high speeds
just like a jet engine. At climb speeds MOST of the drag is coming from lift
and the fact you are raising a heavy weight. The airplane and everything
in it. The aero drag of a large flap opening under those circumstance is of
minimal importance yet the demand on the cooling system is a maximum. You then
WANT a large opening. No fixed orifice of any kind is going to fit the bill.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org