ACRE NL wrote:
I am not here to solve the cooling problems on
an air cooled engine Cozy.
Bug Nat Puffer. It is his responsibility. If you
want to cool your
13B use a P51 scoop. Sorry about the drag.
Paul Lamar
Give it up, Chrissi. If it doesn't work, I'll buy Paul
another "told you so"
badge and buy a chainsaw. If it does work, I'll
publish detailed results and
buy a "nah nah na nah nah" badge for myself. In
the meantime, build your
strakes. :)
Regards,
John Slade
OK I am feeling a bit better now. Been sicker than
anyone should be and still be alive.
Pay attention. I am only going to talk about this
once.
Here is how to cool an AC engine Canard about
as well as can be expected
using the belly NACA duct. Divide the flow into
three parts beyond the lip. Center for
the carb. Duct the outer two to closely fitting muffs
that just fit the bottom
of the cylinders. Parts of this may have to be made
from SS. Wrap the
relatively thick 321 SS exhaust pipes with high
temp insulation and keep them
out of the closely fitting muffs that just fit the
bottom of the cylinders.
The exhaust pipes are heating the air before it
gets a chance to cool
the cylinders and valuable cooling air is escaping
around the exhaust
pipes openings in the cowl. They must be
isolated.
In no way shape or form will this work for rads and
a rotary. Don't even try.
This is what you must go through to make a down
draft cooling system engine
work in an updraft cooling system airplane.
Special updraft cooling
system engines with exhaust ports on top of the
cylinders are available
in certain sizes for use in updraft cooling system
airplanes. Duh!
If you think this is a lot of trouble use two P51
scoops on the top of
the cowl and cool the O-320/IO-360 like they were
designed to be cooled.
Down draft cooling! Use a boat tail with vertical
cowl flaps. Now you won't
have to worry about the exhaust pipes heating the
air and leaking off
valuable cooling air. Use a small belly NACA duct
for carb air.
Paul Lamar
I think there is a Vari-EZ guy in Texas who has had
a lot of luck
with downdraft cooling. He has scoops on top of the
strakes.
I always thought it was backwards, taking low
pressure air from
the top and exiting into high pressure at the bottom
(in a canard).
But since my knowledge of air-cooled engines is so
limited I
didn't realize the engines were designed for
downdraft cooling.
Makes sense since most airplanes are tractors.
Great info Paul, but let's get back to the future:
water-cooled
rotaries!
--
Perry Mick
Duckt N7XR
http://www.ductedfan.com
Let me tell you about my Idea about cooling the Cozy.
>From the start I intended to put all my efforts in to
reducing the under the cowl pressure with active air
outlets: On the turbo side with exchaust augmentation
and on the other side with 6" electric inline blower
rigged to extract hot air on demand.
Also the intake on the NACA will be made with movable
lip able to vary the opening from a scoop, to reducing
the inlet on cold days to controll engine temp.
Bulent
Won't work bulent. Don't do it. You will waste your time.
Could hurt that rare Cosmo two rotor you have on first flight.
Put a P51 scoop on it. You can buy these beauties off the shelf
as hood scoops from the Hot Rod industry.
Paul Lamar
This one should work fine. Turn it upside down and glue it to the bottom
of the Cozy. Foam the inside to smooth the walls of the duct.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org