Stan Blanton wrote:
Hi all,
Here's my first post to the list.
I was looking at the Racing Beat web site and saw they have aluminum housing available. What is the experience with these? Things like heat transfer and thermal expansion come to mind. I know they are real expensive but the weight savings is attractive. Is there any data out there on these housings?
Stan Blanton
A Rotary Wannabe
Jim has several hundred hours on the dyno at the 300 HP per rotor level.
300 HP per rotor? How do they get that much?
Easy! Crank up the boost. The rotary is a very robust structure and will tolerate
a lot of boost with out self destructing in the hand grenade mode.
The turbo record is about 400 HP per rotor. Lots of boost, nitrous oxide, alcohol
fuel and 10,000 RPM. I think even that record will fall with the new light
weight RX8 rotors.
But I don't know anybody rich enough to have run them in an aircraft yet :-)>
Alturdyne claimed they ran some in a one rotor BD 5 motor but I am
not sure if it flew. Their main business was gen sets.
Here is an idea I had a while back. The cut away shows what you must
do to get the water to go where it is supposed to go.
Paul Lamar
Paul that is something we had thought about as well. The steel would give a good surface for the seals to ride on.
By splitting the housing in half it would be easier to cast the aluminum. Or even mill a billet.
The sealing between the two parts would be the major drawback.
It's also possible to harden the aluminum to wear better than the steel.
Is anyone else working on lightweight housings?
Royce
You just need four extra teflon encapsulated silicone O-rings per rotor.
Everett Hatch built some light weight end housings. Power Sport may still
own the casting patterns.
Paul Lamar
Here is a picture of Everett's engine. It is much much easier to cast
or mill two piece end housings if you use peripheral intake ports. Peripheral
intake ports also get you a lot more N.A. HP. Up to 120 HP per rotor at 6000 RPM
and 170 HP per rotor at 9500 RPM. The P-ports shown here are good for about
107 HP per rotor at 6000 RPM.
That's good info, and very interesting.
Anyone care to explain about peripheral ports, what they do, what they look like, etc, to us rotary newbies?
Royce Wise
Peripheral ports are straight shots into the intake chamber through
the rotor housing. As such there are minimal pumping loses. Volumetric
efficiencies are typically over 120% over a wide RPM range. They are
not used in Mazda street cars as the idle and low speed running are
affected. See the web site for more pictures.
Does the engine just idle rough, ar at a high RPM?
It idles rough and misfires often. Power Sport moved the throttles into
the rotor housings near the ports which made a great improvement.
4000 RPM and up is fine.
You can make your own or you can buy new rotor housing from Racing Beat
that have been modified. Power Sport builds their own and they are the
secrets to their obtaining 215 HP at 6000 RPM with a N.A. engine.
That makes a lot of sense. I wondered about the way the intake ports were formed. We have 2 12A engines one is out of the vehicle and the other is still in an 83 body. We just bought them recently and have not had time to open up either. We will be opening the one that is out of the car soon. the one in the car
runs good, and starts easily. It smokes bad, but that is flooding because the carb overflows into the engine. Stopped running it as soon as we saw that. Will stop the flooding change the oil and run it again. It seems to be a good engine the radiator is still completely full of antifreeze and it was full of
oil.
We will probably put the one that is in the car on a test stand and see what we can do to increase it's power in the N/A mode before looking at hanging on a turbo.
We like turbo's and have several Garretts of assorted sizes and A/R's..
Royce
Is it blue smoke or black smoke? If it is blue smoke the oil scraper
O-rings are dried out and cracked. No big deal. It will just smoke when
started up for awhile. Early O-rings were made from neoprene which
got old after 10 or 15 years. Later ones are better material. Best is the
teflon encapsulated silicone. Also check the little nylon lines that feed
crankcase oil to the carb float bowl from the metering pump. They get brittle.
crack, leak and that will wear out the rotor housings and apex seals
due to apex seal lube starvation.
It's black smoke Paul, and you can see fuel pouring into the trottle bores. Float not shutting off the fuel it appears.
At idle it runs very rough, but get it up to 3K and it smooths out because it is able to burn all that extra fuel.
Royce
Those carbs are a mystery to me. There is a guy in Tucson named Paul Yaw
that is an expert with those things. Be careful when taking them apart.
There is a center bolt holding them together. Probably just
crud in the float bowl or a leaking float needle.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org