I spent quite a while chatting with this guy, Micael Murray at OSH. He
was
also exhibiting a turbine but was also talking realistic numbers. He had
a
"firewall aft" display suitable for a Long-EZ or other pusher on display
that
is slated to go into a factory Velocity. WOT flights in a Long-EZ would
be
very short, something like 24-30 GPH.
What is more interesting is his other research into "propfans" like the
8
blade unit he is currently working on.
An intrigueing quote "It was designed specifically for use on the little
T-62T-32 turboshaft engine, but could be used with any engine capable of
turning it at 6000 rpm, and possessing a small frontal area; perhaps a
small
rotary."
Check him out:
http://home.digital.net/~murray/project.htm
...Chrissi
Small turbofans have the same scale boundary problems Monty mentioned. I
doubt seriously
that Williams will get the .5 pound of fuel per pound of thrust they
claim for their small turbofan engine. They refuse to give me test numbers
even though I have asked for them for the past three years at OSH. The
engineers
recognize me coming and and exclaim: Oh no! Not Paul Lamar! He is going to
ask
us what the actual fuel burn is again. Frankly they have scammed us for
100 million
of our tax money.
Paul Lamar
Actually,
Michael and I have communicated on the phone and via email several times.
His prop fan is an interesting project. If you are not going at least 300kts
it is not as efficient as a propeller. At or above 300kts to around mach
0.8 the prop fan is attractive. The solar T-62 does not have enough power to
load the disk properly. You need at least 200-260hp for a 32 in fan. Trying
to go 300kt on 200-260hp is a challenge indeed. If you installed this fan
with a direct drive rotary it would work, but the aircraft would have to be
specifically made for the combination. Tip speed needs to be below 800ft/s
to maintain subsonic flow over the blades. This means 32 in for 6000 rpm. To
keep the power loading where you want it, you can't go to more than 2 rotors
or turbo-charge without increasing dia. To do this you will need a reduction
drive and a bigger fan, which negates the benefit of the direct drive fan.
A peripheral port two rotor, direct driving Michael's fan will work for the
following aircraft which carries one person and has ridiculously low drag
numbers. Top speed 300-325kts depending on cooling drag. I could make it go
a little faster by sacrificing the stall speed, which is around 55-60 mph.
If I let the stall speed be 80 I might get a little more speed. The majority
of the drag is caused by the fuselage on this design, so it is relatively
stiff with respect to wing changes (within reason) Using the prop fan would
also reduce climb and take-off performance vs a variable pitch prop.
Compared to a fixed pitch speed prop, it might actually be better. If you
loose a blade on something spinning at 6000 rpm while traveling at 300kts,
it could get your attention {8-0!!. Might be kind of fun to give the
Questair folks some competition with a rotary :-) Mine only caries one
person and 50 lbs of baggage, so buy two and fly formation! Hell the whole
engine for my bird would cost less than a cylinder assembly for one of those
things, and you probably would burn less fuel flying two of these than one
Venture.
Can you imagine what this thing would sound like?
Monty
I think to get the drag down in the transonic speed ranges where ducted fans
become more efficient than props.... you are going to need swept wings.
Here is an idea I had quite some time ago. The airfoil needs modifications
for the transonic speed range. It also uses an aux fan with an exhaust driven
turbine on its outer diameter for a turbo compound effect and lower fuel burn.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org