Subject: 2 cycle oil air cooled or water cooled?
From: ACRE NL
Date: 3/17/2002, 5:26 PM



Hi Harley, based on your comment about Super Tech and its
reasonable
price I went checking further.

It appears that it is a Pennzoil 2 cycle with Super Tech as
the
Wal-Mart Brand name. See this registration for the oil:

R-99343A WAL-MART SUPER TECH OUTBOARD 2-CYCLE OIL TC-W3
PENNZOIL-QUAKER STATE

I intend to go check it out and see if I can find a
difference
between its $5+ /gallon cost vs the $18+/Gallon Marine
Pennzoil
since both are a 2 cycle oil apparently made by the same
company.

Ed Anderson


Hi Ed, Tracy, and Guys (and Girls),
   I thought that I would also post this to ACRE for those who
don't subscribe to both
lists.
   I raced motorcycles for 20 years (no kidding!!!) and worked as
a professional
motorcycle mechanic while I was in college.  Up until about 4
years ago the 2-stroke
was KING in motorcycle racing.  We went to extreme lengths to
promote both
longivity and HP, which are obviously at odds.
   Let's take a moment to look at the 2-stroke beast to help us
understand the oil and
cooling requirements.  Since a 2-stroke fires on every revolution,
there is less TIME
for the piston, head, cylinder and spark plug to cool down between
firing events.
Due to this, spark plug heat range is very important (it can't be
to hot or it will not
have time to cool between firing) but more importantly, the piston
and rings must
have time to cool down.  Well, since there isn't much time (that
ugly word again) the
piston runs very hot so we are forced to run a very rich mixture
(up to a bsfc of
about .65) to cool the piston and rings.  If the heat gets a
little out of hand, you will
burn a hole thru the top of the piston crown (as me how I know
this!) - the piston gets
REALLY hot.  OK, now for where I have been leading you - the
piston is very hot
which causes the oil to burn off leaving deposits on the rings and
in the ring lands.
This of course causes the rings to stick and compression
disappears.  What does oil
have to do with this you ask?  Well, the oils formulated for air
cooled engines fight
these deposits much better at the higher temps.  But they are not
as suited to a
cooler environment because they will not burn completely and then
gum up the
engine.  The oils formulated for water cooled engines have the
opposite problem -
They burn great at the lower temps but leave deposits in the
really hot
environments.  I found that a synthetic called Golden Spectro
seemed to work best
in both my water cooled bikes and the air cooled bikes (I rode
both depending on
whether it was moto cross or cross country events).  Strangly
enough, the worst
condition of all for the rings was an overly rich fuel/air mixture
because the egt's
would stay so low that the rings would gum up.  I never did find a
cure for that
except to pay attention to the jetting.
   We are told that the apex seal runs at ~ 500 degrees so I
believe that an oil
formulated for water cooling is better suited for our task.  I
will probably run Walmart
Outboard oil - I just don't think that we are stressing the
capabilities nearly as much
as the 2 stroke outboard motors so why pay more.
   BTW, I wil be running Golden Spectro in my Kawasaki powered
miniMax when I
get it finished.

Ken Powell


To add a little evidence Tracy complains that the oil level in his
pan increase
as time goes on as unburned apex seal 2 cycle oil finds its way into
the pan.


        Too much 2Cycle oil in fuel, Virg

The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org