Hi Harley, based on your comment about Super Tech and its reasonable
price I went checking further.
It appears that it is a Pennzoil 2 cycle with Super Tech as the
Wal-Mart Brand name. See this registration for the oil:
R-99343A WAL-MART SUPER TECH OUTBOARD 2-CYCLE OIL TC-W3
PENNZOIL-QUAKER STATE
I intend to go check it out and see if I can find a difference
between its $5+ /gallon cost vs the $18+/Gallon Marine Pennzoil
since both are a 2 cycle oil apparently made by the same company.
Ed Anderson
Hi Ed, Tracy, and Guys (and Girls),
I thought that I would also post this to ACRE for those who don't
subscribe to both
lists.
I raced motorcycles for 20 years (no kidding!!!) and worked as a
professional
motorcycle mechanic while I was in college. Up until about 4 years ago
the 2-stroke
was KING in motorcycle racing. We went to extreme lengths to promote
both
longivity and HP, which are obviously at odds.
Let's take a moment to look at the 2-stroke beast to help us
understand the oil and
cooling requirements. Since a 2-stroke fires on every revolution, there
is less TIME
for the piston, head, cylinder and spark plug to cool down between
firing events.
Due to this, spark plug heat range is very important (it can't be to hot
or it will not
have time to cool between firing) but more importantly, the piston and
rings must
have time to cool down. Well, since there isn't much time (that ugly
word again) the
piston runs very hot so we are forced to run a very rich mixture (up to
a bsfc of
about .65) to cool the piston and rings. If the heat gets a little out
of hand, you will
burn a hole thru the top of the piston crown (as me how I know this!) -
the piston gets
REALLY hot. OK, now for where I have been leading you - the piston is
very hot
which causes the oil to burn off leaving deposits on the rings and in
the ring lands.
This of course causes the rings to stick and compression disappears.
What does oil
have to do with this you ask? Well, the oils formulated for air cooled
engines fight
these deposits much better at the higher temps. But they are not as
suited to a
cooler environment because they will not burn completely and then gum up
the
engine. The oils formulated for water cooled engines have the opposite
problem -
They burn great at the lower temps but leave deposits in the really hot
environments. I found that a synthetic called Golden Spectro seemed to
work best
in both my water cooled bikes and the air cooled bikes (I rode both
depending on
whether it was moto cross or cross country events). Strangly enough,
the worst
condition of all for the rings was an overly rich fuel/air mixture
because the egt's
would stay so low that the rings would gum up. I never did find a cure
for that
except to pay attention to the jetting.
We are told that the apex seal runs at ~ 500 degrees so I believe
that an oil
formulated for water cooling is better suited for our task. I will
probably run Walmart
Outboard oil - I just don't think that we are stressing the capabilities
nearly as much
as the 2 stroke outboard motors so why pay more.
BTW, I wil be running Golden Spectro in my Kawasaki powered miniMax
when I
get it finished.
Ken Powell
To add a little evidence Tracy complains that the oil level in his pan
increase
as time goes on as unburned apex seal 2 cycle oil finds its way into the
pan.
Paul Lamar
Hi Paul,
I see Tracy told you about his "Oil producing" engine. He swore me to
secrecy as I am certain he though he would catch unmerciful ribbing from you
if he went on the list claiming his engine was producing oil {:>). I have
noticed my oil level never decreases and may even be slightly increasing. I
guess if you went long enough between oil changes you could get to the point
that the lubricating oil in the crankcase might get too diluted with the 2
cycle oil to provide good protection. But, at my rate of oil level increase
oil change will come long before than happens. Another bonus point for the
rotary?{:>).
Ed
I would not worry too much about it. Regular motor oil has high pressure
"secondary lubrication" additives mainly for rubbing wear such as cam shafts,
lifters and valve stems that are not needed in a rotary. Zinc and phosphor come
to mind. When burnt I suspect these are what cause most of the gunk on the rotors.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org