Oh I see you bought one of the Lincoln 175 good deals at the show. Great
welder.
I'll see what I can dig up. Here is one from Marc ?.
Also one from Jerry Hey.
Great, thanks! Yes, the 175 is such a deal. We took the position "show
us we can weld aluminum" and they sure did. The helmet was already here when
we got home and a message on the answering machine asking when they could
deliver the machine. No tax, no shipping. Still not believing it was really
that good of a machine I dragged out some scraps of aluminum extrusion from
the barn.. old nasty stuff, it welded just like the blanks of pure aluminum
they use at the show. I'm a believer. For the price of an engine mount and a
few odds and ends you need for a composite plane, you can buy a great TIG
welder, do it yourself and if you can part with it, sell it when you're
done... that is highly unlikely.
My next question though is given we have this tool, why should we not
make the intake manifold ourselves? The casting is great but with that
aluminum pipe you could make a very lightweight manifold.
...Chrissi
Give it a try. I found it difficult to form the oval, bend the tube and
still get
the flange bolts and turbo in there. Perhaps your HKS TO4 turbo manifold
gives more room than the
stock turbo manifold. I screwed with it for about six months or a year and
never
came up with a good looking part. You will also have an advantage as you
will
have more room over the engine than your typical tractor installation. I
had to get those
pipes right down on the top of the rotor housings. Mazdatrix still has
some flanges
I think.
Not to mention tube bends are a greater radius than pipe bends and twice
the price.
BTW Tom, I got the patterns and core boxes. Looks great.
Paul Lamar
Hey, HEY, HEY!!! The list is back up again! Now I can get some long
awaited kibitzing. All this talk of the Lincoln 175.... been thinking about
trying some TIG welding. How much is this beast? And, more to the point,
have you tried Inconel with it yet? I'm itching to try something for the
exhaust manifolds after seeing what Bob Darrah put together.
After stripping down my engine I started pricing out seals, O-rings, etc.
STICKER SHOCK. However, I got an on-line quote from Creavey that was more
in line with reality. Thank goodness! Mazdatrix, Racing Beat, and others
price out at ~$500 per rotor for a full overhaul kit. My engine appears to
have very little wear at all. I should be doing the full mic-checks before
rotormotor and will bring along some of my seals for communal contemplation.
There is so little wear I'm thinking of sticking all the metallic parts back
in without replacing. Then it's just the TES rings, a few standard O-rings,
and sheet gasketing. I am one cheap bugger.
Manifolds: I've been working on a layout for the 20B intake manifold and am
thinking of a radical departure. If I join the two runners from each rotor
right at the manifold it will simplify the tubing (half the runners), the
casting (avoids all the bolts in or near the runners), and makes for a
generally cleaner layout. It will also require larger diameter runners to
port the air. BUT.... are there any compelling reasons to keep the runners
separate all the way back to the plenum? I asked a couple of folks about
this when the list was down and the speculation was that the separate
runners probably had more to do with tuning the engine to run well through a
broad RPM range (especially with the twin sequentially staged turbos) than
anything else, and that combining them for an aircraft engine should be no
problem. Getting large enough injectors may be, though ganging up two
injectors per runner could be done with little problem and may provide some
redundancy. Thoughts all?
Tom Kendall
Its worth a try Tom. So far nobody has used a high speed pressure sensor
to map the intake manifold pressure pulses except Mazda. Chuck Dunlap and I
were talking about that when we stopped at his place in Thatcher AZ. He has a high
speed pressure sensor but he was not sure what the speed actually was.
Did you get a number on the pressure sensor speed Chuck? Also make and
part number please?
BTW Tom I see what you mean by thinning the pattern flange in your note
that came in the box. Interferes with the core prints. Perhaps I can
take some off the outside.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. Copyright 1998-2002 All world wide rights reserved.
http://home.earthlink.net/~rotaryeng/ http://www.linux.org