Subject: Stationary Gear Removal (20B) / e-shaft splitter
From: ACRE NL
Date: 4/24/2002, 7:25 PM


Tom Kendall wrote:

I can't seem to get the stationary gear for the middle
rotor out of
my
intermediate housing (doesn't apply to 13Bs... one of
those unique 3
rotor
problems).

<Snip>

Tom,
Why do you want to remove it?  When I bebuilt my 20B, I saw no
reason to
remove it.
Don Mitchell

I dunno Don.  I've got this funny thing about taking stuff apart.
Have
since I was a kid.  Drove my parents nuts.

Actually, it makes it much easier to clean the housing, inspect
for warpage,
and to inspect the gear & babbit in the bearing.  I also didn't
know but
what there was some kind of O-ring or gasket in the joint that
needed
replacement.  There isn't.  Got it all apart now.

Tom Kendall


Hey Tom,
How did you split your e-shaft?  I built a e-shaft splitter.
Several people have contacted me requesting a drawing of it, but
unfortunately, my drawing skills are worse than my handwriting stills.  I'm
a Physician, not an engineer!!!  Anyway, if you built a splitter and can
draw, I know several people would appreciate a drawing.  I posted pics
previously but it didn't seem to help.
Thanks,
Don Mitchell


Don
I sure would like to see the pictures of the splitter.
Royce


Here they are.

Paul Lamar

 did it:

Get one 3' length of 3/4" round bar stock (mild steel).  Use a bench grinder
and a pair of calipers to carefully grind down about an inch on one end to
~0.705" diameter.  Doesn't take long, just keep rotating the bar on the tool
rest to avoid flat spots and check frequently.  High accuracy isn't real
important.

Get two threading dies: one 3/4" SAE, and one 18M x 1.5.  I used hexagonal
chasing dies, but you really should use a round threading die, especially
for the metric one (more on that in a moment).  You can also get by with a
1/2" NPT die instead of the 3/4" SAE, but the threads end up very shallow
and may strip out during use (mine didn't... only a single use on it
though).

Now thread each end of the bar stock.  The ground down section gets the 18M
thread.  For some reason, the chasing die I used didn't cut the threads deep
enough and mine binds up in the e-shaft hole after only 2-3 threads are
engaged.  With an adjustable round die I expect I could fix this problem,
but they cost 3 times as much (~$30) and require a different stock to turn
'em.

Finally, get a 6" long 3/4" pipe nipple.  Could be longer if you want, but
not necessary.  On each end of the nipple thread on a floor flange (gives it
more heft, and kinda ends up looking like a nice dumbbell).  Slide the pipe
nipple onto the bar stock, and thread a 3/4" nut (or 1/2" pipe cap if you
used the NPT die) on the appropriate end of the beast.

After taping over the male threads on the end of the e-shaft to protect
them, thread the 18 x 1.5 end of the bar into the e-shaft.  Now grab the
pipe nipple and briskly smack the nut on the top end of the shaft with it.
Start gentle and increase the force of the impact until the e-shaft gives up
and splits.  Real easy.

This is really just a custom slide hammer.  Familiar to anybody who works in
autobody shops.

Tom Kendall

 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site. Copyright 1998-2002 All world wide rights reserved.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org