Subject: Turbo oil drain back specs
From: ACRE NL
Date: 5/1/2002, 6:25 AM


     > >> >Speaking of oil drain back I see
     > >> > now why we are having problems. The Garret or Turbonetics oil drain
     > >> > back fitting is too small and the specified restricator jet/hole may be
     > >> too
     > >> > large for the rotaries 90 psi. It is sized for a 30 psi oil system.

     > >> In the book Maximum Boost by Corky Bell on page 42 fig. 4-4 shows the oil
     > >> line from the engine to the turbo with a .055-.065 restrictor and the
     > >> pressure after the restrictor to be 30 psi.  He relates idle, hot min.
     > >> pressure 5 psi with min. flow 0.1 gal/min and max load min. pressure of
     > 25
     > >> psi with min flow of 0.5 gal/min at the turbo oil inlet.  He said to go
     > by
     > >> the manufacturer's specs.
     >
     > Paul,
     >
     > When you visited Prescott a month ago, I thought I'd solved my 20b turbo oil
     > leak problems.  Not so.  Each subsequent engine run has been accompanied by
     > oil leaks through each oil seal--the hot and the cold section of the turbo.
     > Last week I finally enlarged the Garrett drain size from 1/2 inch to 5/8
     > inch.  Oil is still leaking from the turbo case in both directions, although
     > my scavange pump is more than adequate to handle the total oil drain volume.
     > I checked it again just to make sure.
     >
     > I have long suspected that the higher Mazda oil pressure may be part of the
     > problem.  That's why I installed the .165 restrictor supplied by Main Turbo
     > in the first place.  Gary Main told me that was the smallest restrictor
     > approved for a TE-06.   Now, here's a problem for one of the engineers on
     > the ACRE list: If a .165 restrictor is okay for the typical 60-70 psi
     > aircraft oil system, how much smaller an orifice would supply similar volume
     > and pressure for a 20b's 90 psi?  Any help would be appreciated--including
     > how to go about reducing the diameter of the restrictor orifice (braze and
     > re-drill?).
     >
     > Another alternative may be fabrication of an oil bypass system similar to
     > Corky Bell's diagram on p. 42.  Somehow, I have a feeling that would be
     > another steep learning curve for this non-engineer.
     >
     > Thanks,
     >
     > Tom Parkes
     > Turbo 20b Lancair ES
     > tparkes@earthlink.net


     I don't know how to calculate that Tom. Perhaps someone else
     on here knows how.

     You may have to do this by trial and error. You might have to set up
     a graduated beaker and run the engine for a few seconds and pump
     oil through the orifice and calculate the flow rate from that data.

     Also set up the pressure gages like Corky shows to be sure you are
     getting the required pressure in the turbo. This should pay off in
     the long run if it keeps the turbo alive. All of us doing turbo's
     would be greatly in your debt.

     BTW a lowly 13B stock turbo uses a 3/4 inch drain back shielded from the
     radiant heat of the turbine housing.

     Paul Lamar

Just a rought guess, take the area of the restrictor X 60-70 PSI.   Then reduce the
Area of the new restrictor until you have the same poundage @ 90 PSI.
70 X (1 oriface worth of area) = 90 X (not quite one oriface worth of area).

It's a simple ratio, I know,and neglects all the intricacies of fluid flow, but it's a start.

Thank-you,
-
Chris
microcosman.com

 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site. Copyright 1998-2002 All world wide rights reserved.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org