Subject: A message from Harley Dixon (harley@agelesswings.com)
From: ACRE NL
Date: 6/28/2002, 12:04 PM

Russell Kent wrote:

Paul Lamar wrote:

BTW Harley what do you know about Iomega Predator USB CD-R/RW drives? I have been
busting my buns for the last three days trying to get this to work with
my IBM ThinkPad 560x and the software does not recognise the drive.

I deleted all the software once and totally started over. Down loaded the
12 meg Hotburn off Iomega web site and no luck.

I don't know how in heck they expect to install drive software off a drive
that is not installed in the first place. What is wrong with a floppy
boot loader? Sheessss!

Rumor has that USB CD/RW drives don't work at all.

Should I take it back to Fry's and get my money back?
I would really like to have a CD RW drive for my notebook.

Did you check the Iomega support website?

http://www.iomega.com/support/documents/10657.html

Or perhaps you should have done some research with Google:

http://pag.lcs.mit.edu/~adonovan/toshiba.html

But then I suppose it's easier to vent here and let *us* do the grunt work... :-)

Russell Kent

Hey I have paid my dues on this. Yes I have gone to Iomega support and I have exchanged
a dozen messages with them but they keep going around in circles.

Here is the latest set of "instructions."

-----------------------------------------------------------------------------------------------
I understand that you are getting yellow marks in the device manager against the
USB drivers.

Please note that there is no issue as such for the IBM thinkpads with the Iomega
USB cdrw drive. The drive should work properly with the IBM Thinkpad. 

Regarding the problems you are facing, please follow the steps given below to
resolve the problem:

1. Disconnect the Iomega cdrw drive from the computer. 
2. Boot to Windows Safe Mode by pressing the "F8" key at the time of booting the
system.
3. Within Safe Mode, go into Device Manager. 
4. Under the Drives category, remove the yellow marks where ever they are present
against the Iomega cdrw drive. 
5. Under the Hard Disk Controllers category, remove any drivers referencing
Iomega. 
6. Under the Universal Serial Bus category, again remove any drivers referencing
Iomega. 
7. Open the Control Panel and double-click Add/Remove Programs. 
8. Highlight the Iomega Hotburn software listed and click Add/Remove. 
9. Click through until prompted to completely remove the software. 
10. After the software is uninstalled, do a Search for the hotburn files. 
11. Remove all references to these files. 
12. Open the Temp directory (C:\Windows\Temp). 
13. Delete all files in the Temp folder.
14. Empty the Recycle Bin.
15. Restart the computer. 
16.Install the Iomega Hotburn software through the ftp link provided to you. It
is also given below:

ftp://ftp.iomega.com/english/hotburn-w32-x86-233.exe

17. Double-click on this file to install.  
18. Shut down the computer, connect the drive, and reboot. 
19. After the computer has fully booted and recognized the drive, insert a
brand-new CD from the list of compatible CDs given in the link below:

http://www.iomega.com/support/documents/10706.html
 
20. Try to use the drive.

If the problem is still not resolved, then please do contact us for further
actions.


Sincerely,
Henry
Iomega Customer Support

-----------------------------------------------------------

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site. Copyright 1998-2002 All world wide rights reserved.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org