Subject: Tension Bolts One rotor?
From: ACRE NL
Date: 6/29/2002, 5:30 PM

Royce Wise wrote:

Paul, here is some more discussion on the single rotor
Royce

david mccandless wrote:

Hi Tom,
I saw you mse re weight concerns; I spoke with Paul L at some
length on this subject a few weeks ago as I have a similar problem with
my Europa. Frank says his engine is around 135 lbs, so with a light
redrive it will be around 160. I've been working on a simple ignition
system, with a trigger on the front pulley so that should save a few
more pounds when we throw away the distributor and use the hole as an oil
filler. Just today Mark Wiese said that a later model has the triggers
on the pulley so that should help; when I get a little more info I'll
talk to Tracey C about ECMs to suit.  Also the cooling system can be
much smaller capacity, so less water, less hoses with smaller dia. will
all help the problem. So I think you should stick with us for the
present. I have a 2.4 L VW engine kit in a box too, but prefer to go
rotary. Coils: the racers here say many coils can be used but the Mazda
OEM seem to last longest and cost about the same as Bosch, US$30 each
prox.this side of the Pacific and we only need two, so less weight. BTW,
the racers I spoke with
do not use a resistor type coil.
For Frank: Your GM Ignition system. Do you use the original 2 rotor
trigger in the distributer housing and what engine does your GM coils
come from?
For Fred O: Your are right Fred, I screwed up, the Rotor housing+center
plate is about 130mm; I have measured that many things this past
week..... Bolts: ARP have my vote for supply if possible;the racers seem
to prefer studs, I'm not fussy but I feel that Mazda would have done the
research so I tend to lean their way and go for bolts. But if ARP have
studs the right length in stock then studs it is.(might be why the
racers use studs).
Francois St-Germain wrote:


I am interested too I want 36 bolts.
Great job guys!

I use GM ignition system.
As long as you use a transitorized coil it should
works but there are model which are better tan the
other for our application.

Frank
--- david mccandless <daval@iprimus.com.au> wrote:


Hi Tom,
I'm interested, I think hi tension carbon steel is
the way to go, the
same as Mazda uses, the SS and Titanium may have
different thermal
numbers and could upset the tension loads.  I have
not torn down my
engine yet, but as I recall, the length you want for
the two long ones
will be the original length minus 140mm; ie minus
the thickness of one rotor
and the center plate. BTW, I,m researching ignition
systems at present,
you will see some stuff on the group. There is
potential to simplify the
system and save a bit of weight.

Tom Webber wrote:

I found a business in Texas that will make the
bolts we need.  I need to now what type material to
have them made out of, Stainless, Carbon steel,
Titanium,  Basically they told me on the phone they
will make them out of what ever we want and they
will roll the treads.  We need 17 per engine right,
but two of these are longer.  So we are looking for
15 at 10mm X1.00mm X140mm and 2 at 10mm X 1.0mm X
?mm. How many of us are interested.  He said their
is no minimum order.  I'm guessing the more we order
the lower the price.  I don't have a quote yet.
They need a description of the part or a drawing.
Let me know guys.

There must be a one rotor mailing list out there :-)

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site. Copyright 1998-2002 All world wide rights reserved.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org