Subject: Please put a safety cable on your engine.
From: ACRE NL
Date: 8/13/2002, 10:41 PM


   he had experienced a
propeller blade failure while en route to Pahrump. He stated that
post
accident examination of the
airplane revealed that 21 inches of a
propeller blade had separated. The propeller is an aluminum two
bladed
McCauley fixed pitch.

According to the pilot, the resultant imbalance resulted in
substantial
damage to the airframe,
leaving the engine hanging by one 3/8-inch
bolt.


This sort of scene has been played in my mind too many times.  I
guess
it's
my physics and engineering background that puts the respect into
this
kind
of out of balance situation.  That being said I've got some kind of
solution that may be what the safety cable is about.  I don't know,
I've
never seen one.

When a prop sheds a blade or part of one, the prop flange end of the
engine
will want to orbit about the new center of mass of that end of the
engine.  This can be calculated if you have an approximate idea
where
the
prop is going to break.  The (in our case) water pump end would only
see
a
sort of gimbal like motion.

If the safety cable were wrapped around the prop flange end at about
the
motor mount station and had enough slack such that the prop flange
end
of
the engine, after throwing a blade, would "orbit" inside the loop of
safety
cable.  Then the safety cable would effectively cage the engine in
the
loop
but isolate the shake from the airframe.  This of course after the
engine
broke loose from the front mounts (yeah I know, this is a stretch if
MY
imagination).  The engine would still be restrained fore and aft by
the
rear mounts provided they had the range of motion both up/down and
sideways
so that the prop flange could do its orbit without pulling the rear
mounts
loose.

All this would maybe give you enough time to shut down the engine
before
it
made the airplane unrecoverable.

The engineering questions arising (assuming a bed mount) are:
1. Is the "tear loose" force of the out of balance prop going to be
higher
than the negative-G design load of the front mount?  On a metal prop
it
could be, on a composite or wood maybe not.  It would need to be.

2. The safety cable loop diameter would be a function of prop
weight,
engine nose weight, and where you thought the prop would break.  I
seem
to
recall that the amount of prop lost in the above event is common?

Well, this turned into a bit of a read.  Am I on the right path with
this
safety cable?

Mike McGee, RV-4 N996RV, O320-E2G, Hillsboro, OR
13B in gestation mode


While I agree that a cable is not a bad idea, the root cause of this
accident is what is not being addressed by the NTSB.

I am pretty sure that McCauley does not make a fixed pitch metal prop
for
aricraft of the Mustang II or RV speed range.  What builders have done
for
many years is have the prop re-pitched beyond manufacturer's limits.
This
has resulted in prop failure litterally hundreds of times.
The only fixed metal prop for this speed range is a Sensenich (Sp?) and
it
has a HARD rpm limit of 2600 rpm.

Don't depend on re-pitched metal props.

Tracy Crook
tcrook@rotaryaviation.com
www.rotaryaviation.com


I heartily agree with Tracy on reworked metal props. Actually in the F1
racing class
a safety cable is required by rules, and metal props are currently outlawed
for
just these reasons. Sensenich has a very good metal prop for the Lyc 360
engines on the RV's without rpm limits I believe. However the Lyc 320
prop has the rpm limit that Tracy stated. Retuning metal props is a full
time
job for a fully staffed prop company - a lot of effort has gone un rewarded
at Sensenich trying to extend the limits on the prop for the 320. - Vance

 
The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site. Copyright 1998-2002 All world wide rights reserved.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org