| Subject: The diesel report |
| From: ACRE NL |
| Date: 9/11/2002, 12:20 AM |
Marc Wiese wrote:I know this is not of rotary interest, but it has some interesting points in it we should keep in mind. I hope a semi-professional rotary conversion could be as appealing and economical. Read it FWIW...... ------------------------------- Subject: The diesel report From: Thomas Borchert (EDHE) 100137,2113 All, Well, I've flown the diesel Diamond and spoken at length with the people at Diamond. I have yet to talk to Frank Thielert, maker of the engine, but here's my preliminary report. First, keep in mind I'm writing this from a European perspective, where - Avgas is 1.70 $ per liter, Jet A1 and car diesel is 1 $ per Liter (3.8 liters to a gallon) - noisy aircraft will cost you BIG TIME in landing fees The short version is: I am very impressed. I flew the Diamond DA 40 TDI (turbo diesel intercooler) composite four-seater with the Thielert Aircraft Engines TAE-125 out of Wiener Neustadt near Vienna, Austria, running on Jet A1. Some observations and information from my interviews: - I wouldn't have thought one-lever-operation is so convenient. The engine basically has a power lever connected not to the engine but to the electronic engine control units (ECU, two for redundancy) and a gauge showing percent of engine power. That's all you really need. Ok, there's RPM and the usual temps and pressures indicated, too, but that's just for fun - all of that is controlled by the ECU software. Basically, you just set "go fast, go slow" (and accordingly "use much fuel, use less"). A setting of 100 percent power continuous is permitted. The ECU will detect "hamfistedness" and correct for it by, e.g., delaying power application a little. A pre-takeoff check is to press the button for "ECU test", which will then start an internal test cycle. The engine is running very smoothly and has "punch" when applying power. - The engine is adapted from a Mercedes A-class common rail direct injection diesel. It has an intercooler and a turbocharger. A reduction gear box reduces max engine RPM of about 3900 to prop RPM of 2300 maximum. This gear box shields most of the diesel-specific vibration from the prop (Paul, the spikes in the spectrum of the engine are more pronounced because of higher compression, but the gear box does away with most of that. Also, the engine is relatively benign to start with, regarding vibration). The aircraft is shielded by special engine mounts. Vibration and noise levels in the cabin are noticeably lower than in your average Lyc or TCM four-banger. Thielert adds/changes about 140 parts on the original car engine, including the crankshaft. Redundancy and fail safe mechanisms all conform to certification standards. The engine runs both on Jet A1 and diesel. The DA 40 TDI will initially be certified for Jet A1 only, since there are no questions about fuel quality standards there. Diesel certification will follow a few months after. - Power is 125 hp, which might seem low, but... The Lyc DA 40 is driven by an IO-360 with 180 hp. The diesel has 125 hp, but is running at a lower RPM and with a bigger prop, thus being much more efficient. They figure an equivalent hp of 160. There is no significant difference in take-off run and climb rate for the two aircraft - until you reach 3000 feet or so, when the turbo in the diesel engine is clearly winning. - Cruise is most efficient higher up, due to the turbo, of course. Figure on something like 140 knots true with a consumption of about 17 liters per hour.
Well there goes the fantastic claims of high MPG for diesels. 17 liters per hour is 4.5 gallons an hour. Given the low drag and the higher prop efficiency of the Diamond this is not out of line with most gas engines. To give you another data point Klause is cruising at 200 MPH and burning four gallons an hour with his O-200 Varieze. PL
Diamond's financial department will make you a neat calculation showing that for a five-year leasing contract in Europe, the fuel savings alone will pay for the leasing rate at 400 hours flown per year. - The engine initially has a TBR of 2400 hours - R stands for "replacement", which is what you'll do. Price for a new one should be around 20,000 $. - The DA 40 Lyc is built in Canada and is offered in the US. The DA 40 TDI will be built in Vienna and will initially be certified only in Europe, not in the US. Certification is expected by September/October. IOW, you'll be able to actually buy and get a diesel powered aircraft in two months, production backlog notwithstanding. Diamond is shying away from introducing a new engine in the US market again, after having suffered a lot with the Rotax-powered Katanas. Thielert, OTOH, partners with Superior Airparts for engine support. The DA 42 Diesel twin, to be certified by end of 2003 (see below), will be certified in the US, too. - The TDI is about 15,000 $ cheaper than the Lycoming version. - The Mercedes engine block is made of aluminum, which makes it so light. Thielert is working on a V8-aluminum block from Mercedes to make a 310-hp-engine. Rumors have it he's also working on an intermediate 220ish hp power plant. - Diamond has big plans and, IMHO, chances at succeeding. They want to be the top single engine manufacturer "soon" and are ramping up production quite a bit. The DA 42 twin diesel should be certificated by end of 2003 - a four-seat light twin consuming 35 liters of Jet A1 per hour (both engines combined!) going 200 knots, with a price tag of 370,000 $. Cowlings for Lycoming engines have been made <g>. Also, they are working on a four/five-seat airframe for the 310-hp-diesel AND a pressurized single-engine jet to be presented by 2005. They are very excited by all-glass-panels and have seen prototypes of "a big avionics manufacturer WAY cheaper" than the Avidyne Entegra. You can probably guess who'll announce that stuff by next year. I've been told amazingly low prices for a full two-display PFD system. Ok, that's all I can think of at the moment. Questions? Thomas Borchert (EDHE)
If the FAA certifies this Mercedes A class engine they will also have to certify MecanAir's Mazda based 13B rotary.
What makes you say that Paul? Funk certified a Model A ford engine in the 30's and that does mean that they have to certify all modelA engines. Vance
The rules must have changed. As I understand it the factory must supply a paper trail on all the parts. As I recall there are two certifications. You can certify the engine but then you must also certify the manufacturing facility. Is Mercedes certifying these parts? BTW A lower RPM larger diameter prop CANNOT make up for THAT much difference in HP. What say you you about that Vance? 180/125 is 144%. Since your average prop is 85% that means the prop they are running is 122.4%. Wow! A prop that can generate HP! 160/125 is 128%! 128% of 85% is 108%. Still... unbelievable prop efficiency. Sounds like bull shit to me. I think the reason the diesel airplane claims the same climb with 125 HP as opposed to the 180 HP Lyc is the diesel has a constant speed prop. Apples and oranges. Not a fair comparison. If they both had fixed pitch props it would be an out and out lie. Not the first time this company has lied about performance. BTW who is Thomas Borchert? Does he work for Diamond? Is this a press release? Paul Lamar The AirCraft Rotary Engine NewsLetter. Powered by Linux. ACRE NL web site. http://home.earthlink.net/~rotaryeng/ Copyright 1998-2002 All world wide rights reserved.