I would
> like to hear a description of the throttle response of PPorted race
> cars. Maybe Lynn, has experience with this. I would rather have
> the EC-2 than peripheral ports , if it comes to that, but I really
> want both. PP's are the best way to add hp, in my opinion. It would
> be a huge boost for the rotary movement if a do it yourself PP design
> that is compatible with the EC-2 can be developed.
> Jerry
I have one Factory periphery port engine in my old car with two 44mm
venturies
in a Webber 48 IDA. The runners are the same length as the side port
(bridge
ported) engine, about 8 inches to the butterflies. There is no throttle
lag in either
engine, coming off idle. The idle speed is 2,000 RPM. A bit high for
aircraft use.
I don't think throttle lag would be a problem in any case. More a
function of off
idle mixture control than runner length. Street car stuff is all off
idle performance.
We have a bunch of accelerator pump stroke and no problems at all. Most
of the
time we are at 7,000 RPM or more when we open the throttle. Even if
there was
some hesitation we couldn't detect it. In the aircraft, the PSRU at
2.17:1 you can
have the idle at 1,000 RPM without dragging the brakes much on the
ground. So
the throttle response off idle will be quite good and seldom used in a
way that
would expose a response problem. On final you could carry quite a few
extra
RPM without generating a great deal of thrust. So if you need to go
around, just
roll on the power and go. You already have enough RPM to obscure any
hesitation. I think the hesitation "problem" is a red herring. I would
mount the
throttle body at the end of the runners and be done with it.
Lynn E. Hanover
Hesitation is one thing but idle stability is another.
They are not really related.
Paul Lamar
I agree. Lynn, in a Van's RV-x with a fixed pitch prop, anything over about 700
prop rpm will cause airliner like approaches & hundreds of feet of float in
ground effect. Can a p-port idle under 1500 with no danger of quitting either on
its on or with sudden throttle opening? I would consider *slight* hesitation
acceptable. Someone (was it you?) mentioned cutting the p-port to match the side
port timing. Shouldn't that solve the overlap problem Paul mentioned in a recent
exchange about this issue?
Charlie England
Charlie you are forgetting that Power Sport has been flying p-ports for
years in RV's. Allan Tolle has flown many times coast to coast and
entered several Sun & Fun races. No landing problems as far as
I could tell. Tracy Crook never idled his RV-4 engine below 1800
to 2000 engine RPM 829 to 922 prop RPM for years because the Ross
gear box would rattle mightily. He also does not slip when landing.
The port timing has little to do with the p-port overlap
problem. This is mainly due to the pocket in the
face of the rotor. That is the main avenue for the exhaust
gases to enter the fresh mixture area. That path is open from
the moment the apex seal passes the lower floor of the p-port
intake until the next apex seal passes the ceiling
of the p-port exhaust. Then the process soon begins again
with the next cycle. In other words it is open the majority
of the time. P-port intake timing has little to do with it.
When the pressures are the same there is no flow.
This delicate balance of pressures is the main
reason intake and exhaust pipe tuning is so critical
with p-ports. It is quite remarkable that Racing Beat
can build a turbocharged 3 rotor p-port engine developing
over 300 HP per rotor on gasoline.
If it can be done on a 3 rotor, then it could be done on a 2 rotor as well.
300 HP per rotor that is.
What is the known record for HP on a 2 rotor?
Royce
On alcohol and NOS about 800 HP.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2002 All world wide rights reserved.