Subject: remote mount belt driven water pump on Rotorway Exec?
From: ACRE NL
Date: 11/22/2002, 9:44 AM


abc abc wrote:

Paul

While the conversation about water pumps is on.

Not sure if it has been spoken about,or even if it`s any good:(.

http://www.fordmuscle.com/archives/2000/08/electricwaterpump/index.shtml

It takes anywhere from 15-20% of an engines total horsepower to drive a
stock waterpump at high
engine speeds. Hmmmmmm really!!(pinch of salt please)

Operating Voltage 4V DC to 14.5V DC
Maximum Current 7.5A
Flowrate 300 gal to 1300 gal/hr @ 13.5V DC
Operating Temperature -5 F to 270 F
Pump Design Clockwise centrifugal with volute chamber
Motor Life 2000 hr. continuous at 180 F and 12V DC
Pump Weight 2lb

Additional benefits: Removal of thermostat, ability to cool engine
after shut down

http://www.daviescraig.com.au/trade.html  has many graphs

More efficient coolant flow could lead to smaller radiator size,
smaller fans and less coolant
volume, ie: Now have the ability to optimise the cooling system for
cost and weight!

Bye

Pssst hey Mister, want to buy this 100 MPG carb? How about the Brooklyn
Bridge? Cheap. I told Chrissis if I ever have somebody upload these
lies yet again I would have to kick him off the list :-)

This is the dumbest one of all. 300 gallons an hour with only .135 HP.
WOW! That is as close to a perpetual motion machine you will ever find.


Paul Lamar

Paul,

  The recent postings by Bill on his water pump testing have been
interesting. One of the tidbits I've noticed that really hasnt been
commented on is the fact that he has done all of this testing using a 1HP
electric motor to drive the pump. He hasnt measured current draw on the
motor but the fact that it works at all would seem to refute previous
comments that using an electric motor to drive a water pump is impossible.

That is an over simplification and an exaggeration at the same time.
What I said was a 12 volt pump at 7 amps, 84 watts, 0.1 HP, is nowhere 
near the the ONE HP pump Bill was using. Ask Bill how heavy the
ONE HP motor is on his table saw. Check page 185 of the McMaster
Carr catalog. 
115 volts 2 amps 230 watts .3 HP, 7 psi 20 GPM.
115 volts 2.7 amps 310 watts .4 HP 11.2 psi 14 GPM.   


Bill says, "At 5594 RPM and 0 head the pump can deliver 44gpm, 31.5gpm
through 2 evap cores in parallel and 20gpm through a single core." He also
says, "I didnt have an ammeter to measure motor current but the 1HP motor
didnt have any trouble driving the pump at 5600RPM." It would be
interesting to know how much power is being consumed by the motor to do this.

  I dont know how realistic (optimistic?) the claims of the various
manufacturers of electric water pumps are. It would seem that if an
electric water pump was as big an advance over the typical engine driven
pump as is claimed by EWP manufacturers that the OEMs would be putting them
on cars. However it doesnt appear to me that an EWP is quite as impossible
as has been suggested in the past. I have this vague recollection that
someone proved mathematically that it would take a motor of something like
7 - 8HP to provide the necessary coolant flow. Clearly that's not the case.

The 7 to 8 HP claims were made by the car electric pump people in their
fraudulent advertising. Some are claiming 20 HP. That is how
they justify buying one of their phony pumps.

  Paul, please dont kick me off the list - I didnt upload anything - just
making an observation.  :-)

Mike Wills

That is it for this subject unless you are smart enough to 
convert volts and amps to HP. I know you are smart enough Mike. 
You are pushing it! Quit wasting my time!

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2002 All world wide rights reserved.