Subject: Tom Parkes Progress Report- Teflon O rings.
From: ACRE NL
Date: 2/25/2003, 7:38 AM


Lynn Hanover wrote:

You [Thomas Parkes --rak] might try making that a 90/10 glycol mix.
Much better
heat transffer. And run a 22 pound cap.

Whoa! Let's look at what running a 90% water, 10% ethylene glycol mix
might do
first.

  1. According to ASTM D11777, the freeze point of a 10% solution is 26
deg F.  I
     dunno where Thomas Parkes parks [ok,ok, no more puns] his aircraft,
but this
     might be a big problem for him in the winter.
  2. Furthermore, that same test indicates that the "slush point" (where
ice
     crystals form in the solution) can be as 30 degrees warmer.  While
obviously
     no ice crystals are going to be forming at 56 deg F, it is likely
that the
     coolant will begin to freeze at 32 deg F.  What most people don't
know about
     the "freeze point" of antifreeze is that it is set in reference to a
hard
     freeze of the material (effectively the "copper pipe burst"
temperature).
     Prior to this hard freeze, however, the solution gradually turns
into a hard
     slush that can easily damage more delicate parts.
  3. Antifreeze manufacturers formulate their products to be used in the
40% to 60%
     solution range.  This is because of the additive package.  It has
all sorts of
     useful things in it like cavitation protectant (nitrite), aluminum
corrosion
     inhibitors (silicates), ferrous metals corrosion inhibitors
(nitrate), etc.
     If one greatly dilutes the antifreeze, there may not be enough of
the additive
     in the coolant to do the job.  For example, ASTM D2809 specifies the
     cavitation and erosion corrosion test for engine water pumps.  Most
(all?)
     automotive antifreeze products meet this standard when used in the
40% to 60%
     dilution.  Over dilute, however, and the package may not protect
sufficiently,
     which could lead to premature failure of the water pump.

Were I Thomas, I'd use a 40% automotive antifreeze solution using
*distilled* 60%
water, keep the 13 p.s.i. pressure cap, calibrate the temperature sender
using a
pot of boiling distilled water, locate the temperature sender as close to
the block
outlet as practical, leave the alarm setpoint at 220 deg F, and sleep
well.

Russell Kent

Well sounds good but if he takes off and it boils over on climb out he is
in deep doo doo. I think he needs more of a margin than that. What is your
reasoning
on only a 13 psi pressure cap?

Paul Lamar

If freezing is not a factor, Water Wetter has the additive package and
improves heat transfer as well. A pressurised overflow tank is also a must
have. My red light is set to 110C(230F).
Paul what temperature can the standard rubber O rings withstand?

Ian RV6A Australia.

Good question on the stock outer ring. I don't know. The inner ring
is silicone rubber coated on both sides with teflon. Should
be good to 500 F but the temp of the ring can be a lot higher than
the water temp as it is between water jacket and combustion chamber.
No telling what the max temp is for the inner groove.

BTW what makes the stock inner O ring different than the Teflon encapsulated
silicon O rings is the encapsulations. Apparently that adds greatly
to the durability as tiny combustion gas leaks past the Teflon do not
attack the silicone. The silicone is protected by the inert
and high temp (800 F) Teflon coating all the way around.

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2002 All world wide rights reserved.