Mike McGee wrote:
(Didn't mean to take so long to get back on these posts. The Pineapple
Racing Q&A are a synopsis of some things discussed at a tech session at
Pineapple Racing (rotary engine builder) in Portland, OR on Feb 22.)
P.S. This got really long...
Since it's my goal to be one of the quietest planes around, muffler info
was high on my list. With race cars having noise limits there is some
experience with quieting the rotary at levels above 200 hp. Rob Golden
owner of Pineapple Racing has been successful at quieting the rotary's
bark. He emphasized that when you get your pipes assembled, you really
need to physically tune the assembly, on a dyno if possible, to get the
best results. This means playing with the location of the muffler with
respect to the end of the collector.
Imagine the wave train of the exhaust pulses as a standing wave. If you
are running a muffler the exhaust pulse wave peak needs to end up in the
first half of the muffler. According to Golden this is critical to really
get the noise under control. Again, you have to try sliding the muffler
back and forth about one wavelength to get the best location on the
pipe. On our test stands we need to be able to move the muffler with
respect to the collector at least one whole wavelength of the exhaust pulse
in order to find the maximum effectiveness in the rpm band we will use the
most. As you might imagine, the more wavelengths you get inside the
muffler the better it should work.
A tail pipe on the muffler is important for completing the setup for
maximum noise abatement. It's length will be a function of wavelength and
will need to be tuned as well.
On muffler construction, I asked what kind they use in order to keep them
in one piece. I didn't get a definitive answer here as the crowd was
surprised at how many mufflers Tracy has gone through. They also had not
heard of SpinTech. I guess even during racing the engine sees enough
throttle changes that it is easier on the exhaust system than the
continuous power settings in airplanes.
On muffler design he suggested that the muffler needed a pre-chamber to let
the pulse expand before it goes through the baffle section. This made
sense to me as I have been thinking that the rotary exhaust is analogous to
a leading-edge-peak saw-tooth wave. If I were trying to flatten this out
in an electronic circuit I'd start with a capacitor branch to drain some of
that peak energy. Some mufflers have a chamber like this. I don't know if
the SpinTech does or not.
The Spin Tech muffler that Brian Trubee was looking at, the Cruiser, gets
real close to what I think we're looking for. For my 2.85:1 motor with
1.75" primaries and a 2.5" collector, I would want 2.5" inlet and probably
2.5" outlet although a 2.25" outlet would probably work as well. That
makes a model 733x or 732x (depending on the inlet/outlet config you want)
measuring 2.25"x9"x16". I'm almost willing to go with the 4" thick model
3333XL at 4x9.5x16 or if you really didn't mind the extra weight, the 5333
at 4x8.5x22. So I don't have to reprint the SpinTech model data you can
look at the configuration chart at
http://www.spintechmufflers.com/spintech/styleimages/index.htm (Note: the
model 5xxx is now the Sport Truck/SUV measuring 4x8.5x22). The models are
listed with overall sizes at http://www.spintechmufflers.com/ .
Tracy, do you remember the model number on the SpinTech you had made? It
looks like the 2.25" thick model in the pics on your web sight.
Wow, that got long winded. Any comments?
Mike
Mike McGee, RV-4 N996RV, O320-E2G, Hillsboro, OR
13B in gestation mode
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2002 All world wide rights reserved.