Subject: Pineapple Racing Q&A- Spark Plugs
From: ACRE NL
Date: 3/7/2003, 11:30 PM


 > When you pull your plugs to see how they are looking/burning, the threads
 > will give you a picture of how your heat range is dialed in.  The first
two
 > or three threads near the tip will be discolored from the heat if your
heat
 > range is right.  A plug too cold will show one or no threads discolored,
a
 > plug too hot will have four or more threads discolored.  This of course a
 > general rule of thumb and your plug use will also depend on how you
operate
 > your engine.
 >
 > Mike McGee, RV-4 N996RV, O320-E2G, Hillsboro, OR
 > 13B in gestation mode


    I tried to help some circle track boys with their Vega Mini Stock a long
time back. They found out I raced a Fiat and supposedly knew something about
carburetors.
The Vega had a Holley that was actually a Weber built under license, so it
was close to the Webber on my Fiat. When I first arrived at the local track,
I asked them what kind of problem they were having. They didn't know what was
wrong. It had no power, and the oil pressure would slowly go away after a few
laps. The bearings were   looking bright after one weekend of low oil
pressure racing.

     I asked if it was too lean or too rich. The team engineer (18 years old)
said it was 4 turns rich. I am thinking that this was in connection with a
bleed screw or something along those lines. The owner removed a spark plug
(stock heat range) and rolled the threads along a paper napkin, explaining
that it quit making carbon tracks on the napkin after 4 turns (revolutions).

     I didn't know what to say. This might tell you how long the plug was in
the engine, or if the ring package wasn't working and pumping oil, or the
timing was way late or a number of things nobody cares about but more likely
all of above, but it doesn't tell you zip about the heat range of the plug,
or the fuel mixture at a given RPM or heat transfer into the aluminum or
anything else.

   I asked the driver to run a few laps to get some heat into the engine and
give me a clean cut going down the back straight as soon as he got max revs.
Four sets of eyes glazed over in unison. I explained that I wanted a racing
pass down the back and switch off the engine and bump it into neutral so as
not to spin the engine mechanically. Then I explained what that meant, and
after a few false starts we got a clean cut and the plugs came out for a
look.

    The engine sounded crisp and sharp. No stumbles etc. The plugs stayed
snow white, like not run yet. I broke off a round tooth pick in the inboard
air corrector and sent the driver (blind in one eye) back out. Big
improvement. Nearly crashed trying to get around the far end with the engine
shut down. Engine stumbles badly coming on the power out of a turn but
obviously better. I ask how much lead you running?  We may be able to cover
some of that stumble with a bit more advance. They don't know. The guy at the
gas station back home did that for them.

    The damper has one line on it and the bracket on the timing cover has 15
through zero, or something like that. We measure the damper diameter. We do
the math. (big crowd forming now). We mark the damper for 30 and 35 degrees.
We check the timing. its 12 degrees total (maybe).

    The advance weights are a ball of rust. I snatch out the distributor and
beat the weights loose with a small hammer. The racer kids had a hatchet and
a really ugly screw driver. We had to barrow the hammer. They panic when I
jerked the wires off. Only the guy back home knows which one goes where. I
put the engine close to TDC and drop in the distributor aimed at number one.
It starts instantly (as it should) and really sounds not only crisp but loud
and crisp. I tell the impaired driver to go easy for a few and bring me that
clean cut.

    Now we are cooking with gas. The plugs are white again. I ask for more
fuel pressure. I can actually see question marks floating around in the air.
Stock engine and stock pump. No adjustments. I change that to more float. I
raise the float level until the boosters start dripping. I twist the float on
it's arm to mimic the liquid surface in the bowl. All of the fuel is on the
right side of the float bowl all of the time.
    It ran good. I suggested more timing when they got a bigger radiator. I
had them add 2 1/2 quarts of oil to account for how much could stay in the
head and turn to foam. It held some pressure for the whole race. Finished not
dead last. They were very happy.

    That was the last time I had heard of carbon on the threads as being an
indication of anything but carbon on the threads, until tonight.

    The airplane engine is going to be at full throttle or more all of the
time. Or more, because some of the induction systems being built are going to
work better than the stock manifold by a good margin. So what would be a good
heat range for an engine that is normally run at full throttle high load for
hours on end? That would be a 100% duty cycle. My race car is maybe 85% or
90%.

    I run ice cold NGKs at $25.00 each. The rotary is blind to heat range
compared to a piston engine. It will run just fine with the wrong tip style
(if it fits into the hole) and the wrong heat range. I have fouled a plug now
and then by pouring in hot coffee and motor oil on cold mornings trying to
get one to start. (there is no choke system on a 48IDA). But even the old two
distributor engines would run fine on my ton of left over piston engine
plugs. N57Gs N82s N80s.

    Plugs that cold, gapped to .010" with a points distributor and no
fouling. I would suggest that no plug hotter than the coldest street plug
available. And then if they run white all of the time, go colder. I would
seat the gasket by torqing them up in an old housing and then install them in
the engine with just a hint of anti seize compound on the threads, starting
right at the first thread.

The color on the plug is lead and some other crap. So even low lead has lead
and it works fine for coloring plugs. We used to run it in the Fiat. If you
run car gas, all you can get is dark, almost black. But clean dry looking
dark brown to black. It's fine. If it stays white on car gas (no lead no
methanol) go colder or richer. Or check the advance. Looking for the engine
builders max or around 25 degrees max. 13Bs can stand a bit more than 12As.


   Check the plugs for tight from time to time. You should never have a
problem. If no carbon will stick to the anti seize compound you can resort to
looking at the porcelain to get a color.

Some extended tips are too long and will touch the apex seal. Or bottom in
the hole and crack the housing. Very bad. Too high a heat range can overheat
the plug and make it stick in the hole or give up pieces of porcelain into
the engine. Too cold is way better than too hot.

Lynn E. Hanover



     When I see the engine builder that supplies half of NASCAR's engines
looking at plug tips through his lighted eye loupe, he is not looking at
carbon on the spark plug threads. He is looking at the porcelain coloring.
Get a Champion flyer with the heat ranges and the pictures are on there.

 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2002 All world wide rights reserved.