George, we will use simple gaskets. Or "one" to be exact. We will still
use the
TES o' rings between the rotor housings and the end housings. The end
housing
plates are sealed with Fel-Pro "KARROPAK".
There are only water passages to be sealed, the combustion chambers are
still
sealed with the factory o' rings. The bolts will still use seals like
the factory
does. The water jacket remains the same volume as the factory.
The plates are held together with the tension bolts on the outer
perimeter, and
the rear bearing support, and the front stationary gear bolts secure
them at the
center. There is also four other bolts scattered between these rings of
bolts.
Don't see anyway the housing plates can move, or seperate from heating
and
cooling.
The wear surfaces are "Hard Anodized" to rockwell 55 to 60, the same as
the
factory end housings, and then lapped with optical grade lapping
compound to the
mirror finish neccessary.
Don't understand what you mean about the inlet areas being difficult?
Royce
Royce,
I don't wish to be a knocker mate but I have some suggestions that you may
wish to consider.
Firstly a surface of the side housing wear unevenly and sometimes well below
a surface finish, more so near the spark plugs. However det gun finish would
be very effective here on aluminium. The idea is to get some depth in the
hardened surface.
On the inlet areas - the wall thickness is quite thin here and it may need
you to leave a little more meat in the aluminium wall to get sufficient
surface areas to seal with.
I think I know the stuff your sealing with, it may work and like you say
it's only water here - but one tiny leak !!
George (down under)
Hi George :-)
Out of about 6 12A engines we have taken apart we have not found a single end
housing with any measurable wear. We have seen several of the 13B's with the wear
you mention.
Don't know if Mazda used a different process on the different engines, or if just
later on the B's.
We have some second gen housingss, (B'S) that are severely worn in several areas,
but a first gen set that shows no wear. Saw some second gen housings at Tracy's
that were worn the same way.
Hard anodized aluminum is not a coating, but a process that changes the metal
properties. It creates aluminum oxide, the same material some sandpaper is made
from. It will cut steel in the sand paper, grind stone form. In that form it is
grainy like grains of sand. In the polished state it is smooth as polished stone,
in effect it is a sort of polished stone. It's hardness is rc 65 and greater,
depending on the process.
Hard anodizing is .002 thick or greater, 1/2 of the process is under the surface
and the other 1/2 grows on the surface itself.
The Det gun process sprays the material onto the surface at such velocities that
some of the particles are embeded in the metal itself. The others cling to the
surface. Carbide can be used for severe hardness.
Hard anodizing is part of the metal itself.
You should have come to sun n fun, :-), you would have been able to see the
models/patterns of the components. (kinda hard to explain this without you
looking at the pieces) The inlet is a P-Port. It uses the factory exhaust port as
the intake port. The exhaust ports are in the end housings, and are in the thick
piece of the housing. No seals are needed.
The end plate gaskets are just a gasket between the plates, a leak here is no
different than a leak in the cooling circuit anywhere. The plates of the end
housings have the coolant passages in the housings and they are not exposed to the
combustion chamber or the sump any differently than they would be in the factory
engine.
The coolant and oil circuits are the same as the factory circuits.
Hope that helps you out.
Royce
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.