Subject: Apex Seals and NOX
From: ACRE
Date: 4/14/2003, 8:11 AM


 > > >    I have several hundred hrs on the 2mm three piece seals but
 > > switched to the 3mm two piece seals and would highly suggest them.
 >
 > >   As for detonation yes it does increase the chance, to eliminate
 > > detonation I have a relay that kills the trailing ignition as it is
 > > near impossible to detonate with the trailing ignition off, also I use
 > > MSD ignition and I use their 8980 timing computer to retard the
 > > leading ignition.
 > >   With this timing computer I can also retard the timing in flight on
 > > long hard climb outs with a dial that runs from 0 to 12 degrees.
 > >
 > >   Ken Welter


"Brian D. Cain" wrote:

 With all due respect Ken, I'm not so certain I agree with all of this.  I've
 had massive amounts of "field" (high-load racing, etc.) experience with this
 area of the rotary engine and I've got some opinions based on that
 experience.
 First off, I'm not certain that removing trailing ignition will completely
 stave off
 any chance of auto-igniting the mixture using only leading plugs.  If spark
 timing is too far advanced for the load being put on the engine with the
 leadings, they will pre-ignite the mixture.  Even with trailing plugs,
 configured
 with a "thin" trail-split timing (having the trailing plugs fire very close
 to
 the leadings instead of 15 degrees apart per the stock Mazda computer

 On the issue of 2mm vs. 3mm apex sealing, for any of you guys that have
 cruised the various Rx-7 forums and lists out there, this has been a raging
 debate
 by the "experts" for quite awhile.  I ran a 3mm apex seal setup in my last
 race engine and the engine held up for quite some time.  The last engine
 we've
 setup, however, still uses 2mm.  From what I gather about it all, the 3mm
 apex seal is a choice if you're looking for 'insurance' where, in the event
 of serious
 engine knock (honestly, with what you guys are running being mostly
 normally-
 aspirated powerplants, you shouldn't have an issue with this whatsoever),
 the seal
 will be considerably more resilient to cracking and shattering at the ends.
 But,
 on the flip-side of the coin, I gather that a 3mm apex seal will wear the
 rotor housing
 out much more quickly and may not be as efficacious for long-term operation.

 Now, with nitrous oxide injection being introduced into the picture, I don't
 think
 that will have any detrimental affects whatsoever.  Depending on the drastic
 temperature drop and the amount of mass that's added to the combustion
 chamber,
 leading spark timing will have to be retarded several degrees.  But,
 otherwise, I
 think it oughta be just fine to run a 2mm apex seal setup with that.
 There's plenty
 of engines out there that run higher turbocharged boost pressures, with
 hotter
 intake temperatures (ones that may want to induce serious engine knock), on
 2mm
 apex seals that run just fine without any hint of problems.

 That's my $0.02 on it.  Hope it helps,

 > Brian Cain


   Yes like I said I have about five hundred hrs flying on the 2mm
seals but I just like the extra insurance of the 3mm but I also have
about five hundred hrs flying on 3mm seals and they seam to work fine
to with no excess wear.
  As for the trailing ignition, this is not something I dreamed up on
my own as it was suggested to me by Skip Gorman and by Rob Golden and
I can tell you from experience that when I got detonation on a hard
climb out without NOS that the detonation would stop instantly when I
killed the trailing ignition and if I turned it back on it would
start detonating again, also I fire the leading and trailing at the
same time so it has noting to do with timing.
  The theory that has been explained to me is that trailing plug is to
burn up all the gas at the tail edge of the combustion camber and
some fire may be getting around the apex seals to cause the
detonation and by not burning all that fuel mixture back there it is
leaving a safety cushion to stop the leakage but all that is theory
and all I can tell you is it works, done it did it been there.

  Ken Welter

 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.