Subject: Aluminum end housings
From: ACRE
Date: 4/16/2003, 1:48 PM


Sure, only with the surface hardened to RC55.
Royce

7075T6 is the hardest aluminum around and it is Brinell
150. RC 55 is off the Brinell scale with the standard 10 mm ball
and
is Brinell 546 with the Hultgren ball whatever that is.

http://www.cknife.com/compare.htm

Paul Lamar

How Right you are Paul. I wonder what magic aluminum this is! Hard
anodize is the toughest
surface, and it stinks as a running surface.  7075 also doesn't take
coatings or anodize well.
Bill Jepson

Why would you think it stinks as a running surface Bill?
And why would you say that 7075 doesn't anodize well?  It is hard
anodized in numerious applications
in the aerospace and industrial applications for it's excellent abrasion
abilities when hard
anodized.
Royce

Mark Wrathall wrote:

Hi Royce. Glad you are still answering questions on this subject. We all
want the 6.5B project to be a huge success, but talk of anodized Al as a
poorly lubricated, heated wear surface raises a lot of alarm bells.

Could you please post pictures of your patterns and parts you displayed at
SnF for those who couldn't make it.

7075 is not a castable alloy.

Remember that the wankel's first 20 years were hindered by material
compatiblity issues until Mazda finally got the right mix of seal and
running surfaces, They had a team of very good engineers working this issue
with the support of test cells and a prototyping budget. They came up with
nitrided cast steel/iron as a side housing wear surface. What will your
prototype engine cost you with the anodized side housings? If you can afford
it (and we can see that you are convinced) we would love to see the result
of an FAA Part ?? type 50 hour endurance test. Please don't fly this
configuration without stressing it on a test bed and then doing a teardown.

Regards,
Mark


Hi Mark
Glad you are still interested.
Hard anodized aluminum is as hard as case hardened steel, the stuff gear shafts
are made of and some bearing races.
Color anodized aluminum is no where near as hard as the hard anodized stuff.
Different process (well some different anyway) for different reasons.  Color
anodizing adds color to the surface that lasts far greater than paint. It also
protects the surface from some corrorion.  It scratches easily tho.
Hard anodizing makes a good wear surface. It was developed for that purpose. In
the textile industry it is used on thread rolls where the threads are pulled over
the rolls in making carpet, nylon belting and the like.
They used steel rolls for years but they would not last. Hard anodized rolls run
for years with very little wear, and in some cases the rolls are heated.  There is
no lubrication on the rolls.
Hard anodized aluminum is as hard, or harder than the nitrided cast iron wear
surfaces used by Mazda.

We will post pictures shortly.

We are not casting the housings, we are using 7075 T-6 plates. Two per housing.

Attatched is a scan from Racing Beat on their aluminum end housings. It might
clear up some questions Paul has on their process.
They are high dollar castings.
Royce

We have the engine test cell about half completed. It will be used to run the
engine under full power at WOT but only for 40 continous hours and not 50.
I would not fly the engine even then, I'd want further proof of concept first, but
that will tell us if it will hold together as well as hopefully bring out any
problems with it. Remember that we are using the factory rotors, rotor housings,
and about half of the factory e-shaft along with the factory oil pump, chain,
metering pump, bearings, o-rings, seals flex plate etc.

>From Racing Beats Technical manual.

Flame Sprayed Aluminum Side Housings*

We offer a series of Aircraft Grade A356 aluminum alloy side housings to replace
many of the heavier, cast iron stock assemblies found on all 1974 and later 12A,
13B, 20B, and 13G engines. Our housings offer both the obvious advantage of
significant weight savings and greatly increased wear resistance, even under high
horsepower demands.
Furthermore, these housings can be used in conjunction with the stock cast iron
housings, as budgets and applications dictate.
As an example of the significant weight savings: a stock, intermediate housing on
a 1993 13B turbo engine weighs 25.9 pounds, while the Racing Beat aluminum
replacement weighs just 10.5 pounds, nearly a 60 percent weight savings. The stock
rear housing on this same engine weighs 25.8 pounds, while the Racing Beat
aluminum replacement weighs just 13 pounds, again a savings of nearly 50 percent.

After each aluminum housing is cast, using A356 Aircraft Alloy, it is heat treated
to "T-6" hardness and then CNC-machined prior to being flame-sprayed and ground to
a final finish. The greatly increased wear resistance is the result of this
aerospace originated flame spray (or plasma spray) process that Imbeds into the
wear surfaces a proprietary carbide material whose durability greatly exceeds that
of the nitride surface found on the stock cast iron housings.
During development testing, and the subsequent application of these housings in
very high horsepower, turbocharged engines, it was not uncommon to find no
measurable wear on these housings. We have found the flame spraying process to be
so effective that we utilize the process on stock side housings with the same
excellent results.
The Flame Sprayed Aluminum housings are offered in a variety of combinations: 1)
with machined water jacket O-ring grooves for the 1974-85 engine applications,
without these grooves for the 1986-95 engine applications; 2) with side ports *
(based on the ,1993 porting configuration) without side intake ports for
peripheral port applications; and, 3) either top or side starter positioning
(20B application). 6-Port configured housings are not offered,

The intermediate housing we offer provide additional material for machining of
injector sockets should your application require such a feature. While our rear
housing has no provision for an oil pressure regulator, you have the option of
mounting a stock Mazda regulator in the side of the pan (wet sump) or using the
internal pressure regulator typically included with most dry sump pumps.
* Note -The housings "as cast" are for peripheral port applications. If you desire
Racing Beat to Street Port, Bridge Port, or J.Bridge Port your housing(s), refer
to page 59 for details on porting configurations available.

 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.