Subject: Sachs air-cooled rotary snowmobile engine specs.
From: ACRE
Date: 5/27/2003, 4:29 AM


Brett & Tiana Campbell wrote:

Hi all,
I recently picked up a Sachs air-cooled (single-rotor) snowmobile engine
originally from an
early-'70's Arctic Cat snowmobile. The price was right, and curiosity got
the better of me.
Interesting contraption--- no inter-housing seals because it's air-cooled,
and the internal
components (ie: rotor and thrust bearings) are lubed and cooled by the
40:1 pre-mix air/fuel
mixture, which is routed through the center of the engine prior to
entering the intake port. I
believe this method is referred to as "charge-cooled and lubricated," but
correct me if I'm wrong.
The basic engine core sans external components weighs approximately 35
lbs, and measures about 13
inches in diameter x about 6 inches thick, with a 12-inch long e-shaft.
BTW, most of the diameter
is cooling fins--- the rotor chamber oval is only about 7 inches x 5
inches, with a rotor width of
just under 3 inches. Only one spark plug is used, and the rotor uses no
oil-control o-rings, only
conventional side, corner, and (single-piece) apex seals. Both end
housings and the rotor housing
are aluminum (even the wear surface of the rotor housing is aluminum, not
plated), with an iron
rotor and solid-steel e-shaft. All bearings are non-tapered roller type,
including those inside
the rotor where it rides on the e-shaft eccentric. I'm not sure if the
apex seals are carbon
steel, cast iron, or some other steel material. Beyond that I don't have
any other specs on this
engine.
Do any of you know what the displacement, rated horsepower, and torque of
this engine is? Also
does anybody have an idea as to the proper running clearances and wear
tolerances of this engine?
Just wondering, because I'm thinking it just might be suitable as a
powerplant for a basic
ultralight, if and when I ever decide to build or purchase one.


Vaughn Mann wrote:

Bret,
 This may be an answer to your search, I'll paste from this address,
http://www.monito.com/wankel/engines.html
and here, http://www.monito.com/wankel/snow.html

Arctic Cat: The early Wankel Panther's smoothness, power, and reliability
made it popular. In 1974 there was a "running change" mid model year to the
295 engine which had a Mikuni 30mm carburetor in 1975. The 303's had
Tillotson HL carburetion. In 1976 Arctic Cat went to a single manufacturer
(Suzuki pistons), squeezing out the F&S. Additionally the Wankel was
unfamiliar to many service people and did not yet have a range of
performance aftermarket parts.

David Wood wrote 11 Mar 1996 to rec.sport.snowmobiles:

Arctic Cat had at least two different rotary engines in several different
models. First there was the 303. This engine was used until '74, I believe,
and after that they used the 295. Both engines were made by Sachs. The
rotaries could be found in Panthers (naturally, what engine couldn't?) and
Cheetahs and probably others such as the Puma. I had a 75 Cheetah with the
295 and there were a few things to look out for. One, the recoil needed to
be well greased at all times. There was a zerk fitting on the top for this
purpose. If it wasn't lubricated the recoil had a tendency to self destruct.
Since the fuel pump is *mechanical* on the 295 and driven by an eccentric on
the end of the crankshaft which sticks through the recoil the recoils are
difficult to find. Two, the fuel pump. If the eccentric bearing went bad the
end of the fuel pump push rod would get worn away and soon there would be no
fuel getting pumped. Both of these problems are easy to avoid with a little
maintenance but would definitely be something to look for if you were to buy
one of these machines. My Cheetah had a boatload of torque and was great for
a work sled. Oh yeah, belts can be kind of hard to find, too, because no one
has the correct one listed for that application and if you do have to
replace a recoil or fuel pump they were about $70 used 7 or 8 years ago.
OMC put 500cc rotaries in both Johnson and Evinrude snowmobiles. They were
very large sleds, but had electric start and reverse to make them a little
easier to live with. These engines came in two flavors, 35 and 45
horsepower. I haven't heard much about the 35s but the 45s had some trouble
with the shaft of the secondary throttle plate breaking and allowing the
plate into the engine thus destroying the rotor housing. I know two people
that seem to have a morbid fascination with these things and have at least
half a dozen of them between the two. Most of them are just used for parts,
however, as only two of the 6 or so sleds are in running shape, so that says
something about the OMCs I would say.
About 15,000 rotary engines were manufactured by OMC for their snowmobiles
and about 125 million dollars were expended for development (equivalent 1997
dollars).-- 

The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.