Subject: Sachs air-cooled rotary snowmobile engine specs.
From: ACRE
Date: 5/27/2003, 4:33 AM


Brett & Tiana Campbell wrote:

Hi all,
I recently picked up a Sachs air-cooled (single-rotor) snowmobile engine
originally from an
early-'70's Arctic Cat snowmobile. The price was right, and curiosity got
the better of me.
Interesting contraption--- no inter-housing seals because it's air-cooled,
and the internal
components (ie: rotor and thrust bearings) are lubed and cooled by the
40:1 pre-mix air/fuel
mixture, which is routed through the center of the engine prior to
entering the intake port. I
believe this method is referred to as "charge-cooled and lubricated," but
correct me if I'm wrong.
The basic engine core sans external components weighs approximately 35
lbs, and measures about 13
inches in diameter x about 6 inches thick, with a 12-inch long e-shaft.
BTW, most of the diameter
is cooling fins--- the rotor chamber oval is only about 7 inches x 5
inches, with a rotor width of
just under 3 inches. Only one spark plug is used, and the rotor uses no
oil-control o-rings, only
conventional side, corner, and (single-piece) apex seals. Both end
housings and the rotor housing
are aluminum (even the wear surface of the rotor housing is aluminum, not
plated), with an iron
rotor and solid-steel e-shaft. All bearings are non-tapered roller type,
including those inside
the rotor where it rides on the e-shaft eccentric. I'm not sure if the
apex seals are carbon
steel, cast iron, or some other steel material. Beyond that I don't have
any other specs on this
engine.
Do any of you know what the displacement, rated horsepower, and torque of
this engine is? Also
does anybody have an idea as to the proper running clearances and wear
tolerances of this engine?
Just wondering, because I'm thinking it just might be suitable as a
powerplant for a basic
ultralight, if and when I ever decide to build or purchase one.


            
Vaughn Mann wrote:

Bret and gang,
Here's some info on the picture of the motorcycle that Paul posted. (great
picture Paul)
Vaughn.
The Hercules (Herkules) works have existed for more than 100 years and are
one of the oldest motorbike works. They belong to the Sachs group who
produce automotive products like clutches, shock absorbers and small engines
for several purposes. Sachs was one of the first licensees of the new NSU /
wankel rotary engine in 1960. They developed and built more than 35,000
wankel engines mostly for stationary purposes. Characteristic was the
air-cooling and the charge-cooled rotor. The biggest one was the 294 cc KM
914 for generators and snowmobiles. This KM 914 was the basis of all
Hercules and BSA (later Norton) rotary motorbikes.

The first Hercules W 2000 was shown at the German IFMA motorbike show in
1970 to see the public's reaction to a rotary bike. It had the Sachs KM 914
engine and a BMW gearbox and driveshaft. Only one prototype was produced.

In 1973 Hercules built 50 W 2000 in a "pre-series" and sold them only to
Hercules dealers. It had the KC 24 engine, which was based on the KM 914 but
was fitted for use in motorbikes. A six-speed gearbox with chain-drive was
now installed. Characteristic for the pre-series bikes was the yellow fuel
tank.

Production began in 1974 with the KC 27 engine. The bike was sold in England
as DKW because that name was more popular in England and Sachs owned the
rights of that name, too. Special motorbikes based on the W 2000 have been
driven in long-distance races and were very successful in off-road sports. A
50,000 km endurance test at the Nürburgring in 1975 showed very low wear.

Hercules made prototype studies with a water-cooled engine in a BMW/5 frame
and a more conventional looking engine on a 7 speed gearbox of the Hercules
GS Two-stroke. For the last year of production the W 2000 got an
oil-injector to avoid the mixing of fuel and oil. Overall 1800 Hercules W
2000 have been built. After stopping the production of rotary engines Sachs
sold the tooling machines to Norton. There is a IG Hercules W 2000 in
Germany, a DKW owners club in England and a "Rotary Recycle" in USA. They
were made at least as late as 1977.

Capacity.......1 rotor x 294 cc
Horsepower.....27 bhp at 6500 rpm
Torque.........35 Nm at 4500 rpm (24.5 ft-lb)
Brakes.........front disc, rear drums
Weight.........174 kg
Max. Speed.....140 km/h - 87 mph
Production.....1834

 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.