Vaughn Mann wrote:
Bret,
This may be an answer to your search, I'll paste from this address,
http://www.monito.com/wankel/engines.html
and here, http://www.monito.com/wankel/snow.html
Arctic Cat: The early Wankel Panther's smoothness, power, and
reliability
made it popular. In 1974 there was a "running change" mid model year to
the
295 engine which had a Mikuni 30mm carburetor in 1975. The 303's had
Tillotson HL carburetion. In 1976 Arctic Cat went to a single
manufacturer
(Suzuki pistons), squeezing out the F&S. Additionally the Wankel was
unfamiliar to many service people and did not yet have a range of
performance aftermarket parts.
David Wood wrote 11 Mar 1996 to rec.sport.snowmobiles:
Arctic Cat had at least two different rotary engines in several
different
models. First there was the 303. This engine was used until '74, I
believe,
and after that they used the 295. Both engines were made by Sachs. The
rotaries could be found in Panthers (naturally, what engine couldn't?)
and
Cheetahs and probably others such as the Puma. I had a 75 Cheetah with
the
295 and there were a few things to look out for. One, the recoil needed
to
be well greased at all times. There was a zerk fitting on the top for
this
purpose. If it wasn't lubricated the recoil had a tendency to self
destruct.
Since the fuel pump is *mechanical* on the 295 and driven by an
eccentric on
the end of the crankshaft which sticks through the recoil the recoils
are
difficult to find. Two, the fuel pump. If the eccentric bearing went bad
the
end of the fuel pump push rod would get worn away and soon there would
be no
fuel getting pumped. Both of these problems are easy to avoid with a
little
maintenance but would definitely be something to look for if you were to
buy
one of these machines. My Cheetah had a boatload of torque and was great
for
a work sled. Oh yeah, belts can be kind of hard to find, too, because no
one
has the correct one listed for that application and if you do have to
replace a recoil or fuel pump they were about $70 used 7 or 8 years ago.
OMC put 500cc rotaries in both Johnson and Evinrude snowmobiles. They
were
very large sleds, but had electric start and reverse to make them a
little
easier to live with. These engines came in two flavors, 35 and 45
horsepower. I haven't heard much about the 35s but the 45s had some
trouble
with the shaft of the secondary throttle plate breaking and allowing the
plate into the engine thus destroying the rotor housing. I know two
people
that seem to have a morbid fascination with these things and have at
least
half a dozen of them between the two. Most of them are just used for
parts,
however, as only two of the 6 or so sleds are in running shape, so that
says
something about the OMCs I would say.
About 15,000 rotary engines were manufactured by OMC for their
snowmobiles
and about 125 million dollars were expended for development (equivalent
1997
dollars).--
-- Brett & Tiana Campbell wrote:
Vaughn,
Thanks for the info. The site was very helpful, and based on your info
regarding carbs this engine is a Sachs KM914B of 303 c.c. displacement since
it uses a Tillotson HL side-draft rather than the Mikuni used on the
later-model 295 engine.
It looks very much like the engine on the race car photo posted by Paul---
same fan and recoil starter, with gobs of cooling fins. BHP was quoted as 19
at 5500 rpm, with 20.3 lb-ft of torque at 4000 rpm.
Previous owner said that the Arctic cat that it was in was one of the faster
sleds around at the time once rpms built up, but bogged down badly at lower
revs due to the weak torque in that range. This testimony comes as no
surprise.
As I mentioned earlier, the engine weight sans fan/starter & magneto
assembly, clutch, carb, and muffler is 35 lbs. Completely assembled weight
with all above components (except for the clutch, which wouldn't be required
on an ultralight) is 67 lbs. This means that a belt-driven 2:1 ratio redrive
would double the torque to 40.6 lb-ft, and provide a total (estimated) F/F
weight including prop and mount of a little over 100 lbs.
Since my knowledge of ultralights is suspect at best, do these figures sound
realistic for that application? What about using it on a powered parachute
or hang-glider?
Again, thank you and everyone else who provided info. This is interesting
stuff!
Brett.
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.