Subject: Sachs air-cooled rotary snowmobile engine specs.
From: ACRE
Date: 5/28/2003, 4:57 PM


-- Brett & Tiana Campbell wrote:

Vaughn, Thanks for the info. The site was very helpful, and based on
your
info regarding carbs this engine is a Sachs KM914B of 303 c.c.
displacement
since it uses a Tillotson HL side-draft rather than the Mikuni used on
the
later-model 295 engine. It looks very much like the engine on the race
car
photo posted by Paul--- same fan and recoil starter, with gobs of
cooling
fins. BHP was quoted as 19 at 5500 rpm, with 20.3 lb-ft of torque at
4000
rpm. Previous owner said that the Arctic cat that it was in was one of
the
faster sleds around at the time once rpms built up, but bogged down
badly at
lower revs due to the weak torque in that range. This testimony comes
as no
surprise. As I mentioned earlier, the engine weight sans fan/starter &
magneto assembly, clutch, carb, and muffler is 35 lbs. Completely
assembled
weight with all above components (except for the clutch, which
wouldn't be
required on an ultralight) is 67 lbs. This means that a belt-driven
2:1
ratio redrive would double the torque to 40.6 lb-ft, and provide a
total
(estimated) F/F weight including prop and mount of a little over 100
lbs.
Since my knowledge of ultralights is suspect at best, do these figures
sound
realistic for that application?  What about using it on a powered
parachute
or hang-glider? Again, thank you and everyone else who provided info.
This
is interesting stuff! Brett.

Your quite welcome Bret!
I'm not sure on the doubling factor of torque but I am sure it would
bring
it up significantly, Paul and the crew can probably help you on that
one.
As far as the weight factors, take a look at the Rotax and Kawasaki
etc.
utralight engines and compare weight with comparable hp ranges.  Most
of
these already come with the redrive built in BTW.  I would like to
know what
you come up with as in the future I'd like to adapt one for the Farm.
All
of the ultralight owners/pilots I talk to always mention the
tremendous
amount of maintenance they perform on the common Rotax to keep them
flying.
I would rather see a Rotary as the power source on mine if I buy/build
one
in the future.  Vaughn.


The torque will double but that doesn't get you any more horsepower. If
it's a 19 hp engine, then you will need an ultralite that will climb &
fly (safely) on 19 hp. Even if you kept the weight to 80 lbs, it's still
pretty bad compared to a 2 stroke rotax.

Charlie England

Brett & Tiana Campbell wrote:

 Thanks guys,
 I've since had an opportunity to go over some of the specs on the 20-50 Hp
2-strokes available and the news isn't all that encouraging. Even though the
hp curve for a rotary is much more useable than that of a piston engine, the
Rotax 277 single-cylinder produces a full 9 more hp than this rotary while
weighing far less. In fact, Rotaxes producing three times the hp weigh less.
Some of the motogliders can get by on 20 hp but again, those engines are
much lighter. Considering that I'm one of those really big guys with a bubba
factor of eleven, in order to get out of ground effect I'd need Nebraska.
Maybe I'll strap it onto the back of a small catamaran and turn it into an
airboat...
Fortunately I do have a ppl, so my original plan to build a 13B-powered
Vision (extended wing) still stands. Any ultralight in my future would be a
side project, unless of course I were to lose my medical.
As for the 45-hp OMC engine, I don't know what the weight is. I do know that
there's a guy in Walkerton, Ontario who has one purchased new in the '70's
and still in the box. I don't know if it's for sale though. This info came
from someone on the Rx7 forum. I've inquired further and am waiting for a
reply. If the price is right I just might buy it for a possible future
project.

The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.