Ed Anderson wrote:
Hi Paul,
As you know, the BurnsStainless bent aluminum tubing is
annealed
to
"O"
condition before bending - leaving it somewhat softer than
desired
for
our
applications. See extract below, it appears that by
sticking it
into a
regular electric (not microwave) and baking it for 8 hours
you
can
get
it
back to T-6 condition. (hate to think what the electicity
cost
would
be).
I think I may try that with my intake manifold just to see.
Ed Anderson
Jim Millett, president of U.S. Light Aircraft Corp., told us
something
that
illustrates the peculiarities one can encounter in the field
of
heat
treating aluminum. He suggests taking a small piece of
6061-T6
sheet
and
trying to bend it with your hands. You will find it to be
very
strong
and
springy. Then heat it to 950 degrees. This could be done in
a
pottery
kiln
or by using a propane torch to heat it evenly until the
surface
turns
gray.
Then immerse it in cold water. This is what is called
"solution
heat
treatment." The sample is now in the 6061-0 condition, the
last
"0"
meaning
that it has been annealed to dead soft and easily bent
condition.
Then
bake
it in a kitchen oven at 350 degrees for eight hours. This is
called
"precipitation hardening" and the sample is now back to the
6061-T6
condition and just as strong as it originally was.
Ed Anderson
Matthews, NC
RV-6A N494BW
eanderson@carolina.rr.com
Funny you should mention that now. I am about to pick up about
120
bends
from the
bender and take them over to the heat treater.
How does it feel in the O condition. Can you easily bend or
dent
the
.058
scrap?
BTW the legs on those bends look very long. What did Burns
charge
you for those bends? I assume you are going to cut them off
around
17 inches.
Paul Lamar
The O condition is soft, fairly easy to ding. They have
probably
age
hardened a tad since I've had them a while. I forget the exact
price,
but
it was somewhere around $27 each. Yes, I am going to cut them
off
at
around
8-9 inches up. I am going to leave the length of the secondary
about
what I
have now as it gives me great torque around 5300 rpm (on cold
mornings
can
get 5800-5900 as I overpower and stall the prop). However, the
primary
loop
will be shorter to try to get a little more power in the higher
rpm
range.
Attached are some photos of the tubes and flange as well as the
ported
casting. I need to see if that brazing rod will build out a
flange
around
the bolt hole along the edge. Then cook it for 8 hours {:>)
Ed
David Barker wrote:
If I rememeber my limited metalurgy correctly, I think the hardening
Aluminum to T-6 takes 8-11 hours at ~900 degrees F not 350 degrees.
Dave Barker
Interesting Dave, that is the temperature (950F) the article states causes
the aluminum to go to the soft "O" condition. In any case, I cooked the
tubes for 8 hours at 350F and they appear to be harder than previous. I
should have put a scrap piece in along to cook with it and then try some
"ding" test and compared it with the "raw" tubing - but, alas that though
did not occur until this morning.
I should be able to find something on the internet about that - I'll give it
a try.
Ed
Well in the one case you cool it rapidly and in the other case you
cool it slowly. I'll ask the heat treater when I pick up my bends.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.