Subject: Mick's oil cooling woes
From: ACRE
Date: 6/2/2003, 8:24 AM


Perry Mick wrote:


OK, after years of fussing with this thing I'm convinced that the oil
cooler to the left of the engine just won't work. I don't have any ideas
where else I could put it, do you?

I bought a differential pressure meter from McMaster Carr, reads out in
0-15 inches of water. I get NEGATIVE 7 inches of water at the inlet, and
negative 3 inches at the exit relative to static.  So the air is still
flowing through the oil cooler backwards. This is exactly the same
result I got over a year ago with an airspeed indicator.  Apparently
that "ram" air inlet under the strake is no such thing. That must a
terrible place to try to get some high pressure air. Maybe the leading
edge of the strake being swept has something to do with it? I did NOT
have the ports reversed, there is truly negative pressure in the inlet.

I think I'm just going to have to hang that ugly thing out in the breeze
under the belly. It is wider than the fuselage of the Long-EZ!

--
Perry Mick

Good old Magnahelix.

I don't think it is 7" negative. That would blow me away if it
were really 7" negative. Something REALLY weird going on. It is more
likely 7" positive in front of the intake and 3" positive  on
the top of the oil cooler with a net 4" across the cooler.


It really is negative. Here is drawing of what I think the airflow does.
 Maybe the airflow is going around the duct, creating a low pressure
area in front of it. There is definitely spanwise flow, I can see dust
tracks on the wings when I fly in a little drizzle. Klaus talks about it
on his webpage - it occurs with swept wings.


I am assuming you are using porous kitchen foam on the ends of
the tube as per the pic below.


No I used 1/8" od aluminum tubes epoxied into the oil cooer duct,
perpendicular to airflow like static ports. The ducting is completely
sealed now inlet and exit sides. I got the same result with an airspeed
indicator last year with different tubes and different mounting.


Ah Ha THERE IS is your negative pressure!!!!  Try Bill's Briggs &
Stratton air cleaner foam. 


OK what is the current condition of the exit of the oil
cooler? Is the pressure tap on the back of the cooler right down on the
cooler it self? It is hard to do this by remote control
without a digital camera.


The inlet is like you show, but I dropped the bottom and made the inlet
5 x 5 square.  What your picture shows is the original 3 x 5. I took
data with an airspeed indicator and that is when it showed the inlet was
lower pressure than the exit. I made the inlet larger and the oil temp
got worse! The exit is now pretty much open to the upper surface of the
cowl.

The question is; Is the necessary large hole in the cowl above the oil cooler?
the cowl is too close to the back side of the cooler to work.

The inlet tap is about the middle of the oil cooler, just 1/2 or 1 inch
below the oil cooler. The exit tap is a couple inches rearward of that
just 1/2" above the oil cooler.


What is a good day for me to fly up to Portland  and mess with
this Perry? This coming weekend? I can meet Mike McKee
and we can all drive  over together to see Ken's new Coot.
Portland mini rotary get together. I'll bring my water manometer
and my digital camera and we can set the manometer in the
back seat and you can take pictures over your right shoulder of
the manometer. I'll also bring my notebook computer so we
can look at the pictures full size. Think about a bracket
over your right shoulder that will hold the camera with
a 1/4" standard tri pod camera hold down screw which I have.


This coming weekend isn't good, it's my son's birthday and the wife is
talking about going to Seattle.


Or I can Fed X the whole works up there and you can Fed X it back
when done. More fun and quicker for me to come up.

It would be fun, I'll have to let you know when a good date would be.

Get some 1/8" plywood door skin and blue foam and we can build a
prototype air exit. Or we can extend the air intake forward
ahead of the the strake. That would be less drag than
mounting the cooler under the fuse.
I am sure I can get this to work.

Let me experiment with it over the next couple weeks before you come up.
I can get good data with the magnahelix. I'm thinking I will first
extend the inlet all the way forward but leave the oil cooler where it
is, that would be the easiest to do for now. I'm very cautious when
building anything external in that area, don't want it to come off and
go through the prop.

--
Perry Mick
Custom Composite Props
mick@bridgingworlds.com
http://www.ductedfan.com

The magnahelix is only one measurement at a time. Hard to get meaningful
data with only one measurement at a time. I can Fed X the manometer
and loan you my camera for a few days as I can use Robin's in the mean time.

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.

Perry-Mick-oil_cooler_ez3.gif