lots of snips..
Yes, I agree, both units come in fairly light, I think. I used a two
throat 4 injector TWM TB when I first started flying, but came to the
conclusion that the two 2" dia holes just did not create enough velocity
of
the mixture to stuff the chambers fully at 5000-6000 rpm. Apparently
worked
fine for the guys turning 8000 and above in race cars. It is certainly
a
nice, well made unit and for your 3 rotor will probably be just the
thing.
Onward to more (less weight that is) progress.
Ed Anderson
I am not going to go there Ed. However if what you and Paul Yaw say is
true
the Lemans engine should fall flat on its face at 6000 RPM but it does
not.
It generates 120 HP per rotor at 6000 RPM. For the math challenged
that is 240 HP for a two rotor. Please repeat that over and over again
so it is burned into your cerebral cortex for future use :)
Paul Yaw has yet to build an engine that puts out as much HP per rotor
as the Lemans engine at any RPM. What is fooling Paul Yaw is he is pumping
air through a carb and carbs need velocity or they don't work.
Paul Lamar
I understand, Paul, and will be the first to admit that my results may have
been influenced by other factors. However, I do know that even with the one
flight I had on the old engine with the current manifold, my rate of climb
increased by 300 ft/min with smaller tubes, longer intake. If I could have
gotten 6000 rpm for take off with TMW I would certainly have stuck with it.
My intake TWM intake from block to thottle body was the lenght of the Racing
Beat Weber manifold - maybe 6-8", so a little short for the LeMan's type
output at 6000 rpm. But sure would like to have that 240 horses. Sigh,
guess, I'll just have to stick that turbo on, next..
Maybe others, like Al, will have better results than I did.
Ed
Its the longer intake runner Ed. Not the smaller tubes. People have been talking
about this for years and every few years Mazda increases the port area and
reduces the velocity and the engine generates more power.
Tracy went into a state of shock and disbelief when I first told him the RX8
engine had 30% more intake port area than even the big port 3rd gen engine :)
If you want a good book get Taylor's "The Internal Combustion Engine
in Theory and Practice." Also H. Heisler "Advanced Engine Tech" a book
I have mentioned on here many times. Intake air velocities can approach
supersonic speeds. It is not as simple as it looks.
Wall friction in the runner plays a major role. The larger the runner the
lower the wall surface area to volume ratio becomes and the higher the flow.
The simple way of looking at it is the ratio of the circumference of
a circle to the area of a circle. The area is pi R squared while
the circumference is 2 R times pi.
Velocity cuts two ways. When the port opens the mass of air
must be accelerated. When the port closes the kinetic energy
in the air mass due to it velocity is converted to potential energy
in the form of a lump of high pressure air. See the rubber ball analogy in
an earlier post of mine. This then rebounds and comes back hopefully
just as the port opens again. Larger runner, larger ball,
lower wall friction losses relative to the size of the ball.
It's like getting hit with a Mac truck going 50 MPH verse a Honda
going 70 MPH. They both have the same energy but the Mac truck is seeing
less friction. One of the rationales for using plastic intake runners
is they have smoother walls than castings. One of the reasons
I designed the manifold in small sections was so the insides
could be polished. Extrude Hone is an expensive process but it
can be used and is used to polish the insides of production
cast aluminum manifolds.
The problem with going on what shade tree engine builders say is they
cannot possibly duplicate what Mazda can duplicate with dozens of dynos
running millions of combinations with computerized data acquisition.
Kenichi Yamamoto recognized this problem from the get go and invested in
a state of the art computerized test facility way back in the late sixties.
Imagine what he was confronted with. A brand new engine concept that
absolutely no one knew anything at all about. I digress.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.