Subject: Perry Micks oil cooler pressure test.
From: ACRE
Date: 6/17/2003, 7:16 PM


This system worked fairly well except for a pusher prop phenomena
which I will describe later.

Paul Lamar


The manometer picture is 80 Kts (92 MPH) on climb out.
The cockpit reference pressure is the left set of tubes.

Exit tap E1 is  showing +1" E2 is +2" E3 is +3" and E4 is +3.5" ??????
Intake taps are I1 is -.5"  I2 is -.5" and I3 is -.25 ??????

Dynamic pressure at this speed is  4 inches of water so the intake
is showing negative pressures instead of positive pressures!!!!!!
A normal intake, and this is indeed a normal intake, should show
about 50% to 80% of dynamic pressure or around 2 to 3 inches
POSITIVE!!!!

What the heck is going on????? My theory is the prop is


dragging air around in front of it in a vortex. This vortex has a
vertical component that is impacting the left aft strake top surface.
This builds a high pressure reverse flow in the boundary layer and is
filling up the back side of the oil cooler.





Al Gietzen wrote:


I'm not saying you're wrong, and I don't have the answer; but I find
this theory Extremely hard to accept.  It seemingly negates the whole
concept of ducted fan.  To create that kind of pressure that far forward
of the fan would be, well unbelievable.  We do know that on the these
canard planes the flow spills down off the sides of the fuselage toward
the rear, and at high angles of attack flows spanwise (outward) in the
boundary layer, but again; it is going there because the pressure is
lower there.

Some tufting in the area of the cooler exit would be very telling.  One
thing to try is a deflector fairing over most of the cooler exit which
is shaped like the top half of an airfoil, which has an exit area about
1.6 times the scoop inlet area.  The airflow over the strake at the
point of the exit has recovered all the pressure lost over the front
part of the strake, so that exit is not in a low pressure area without
it's own deflector.

Also, I think some study of what's going one under the strake is in
order.  What is that rounded protrusion at the strake fuselage
intersection ahead of the scoop?  Could it be causing a turbulence which
decreases the dynamic head at the scoop?

Your theory also suggests the putting the oil cooler on the other side
would give it extremely good flow.

Al

I agree on that last point and Perry and I discussed it. Unfortunately
that area is needed by Perry's intake manifold. Perry's top cowling
is now smaller and tighter than most tandem pusher cowlings.
I think we can get it to work where it is by getting rid of the high
pressure on the oil cooler exit.

You must admit it is hard to believe that a fluid can flow perfectly aligned
axially and then suddenly start flowing in a vortex after encountering a prop.
We all know there is a vortex behind every propellor.

If you stick a spoon in a cup and swirl it around the spoon does
not have to be in the bottom of the cup for the fluid to swirl
around down in the bottom as well. Fluid has viscosity and affinity for
other fluid particles in its vicinity. This is why I think
there is vortex action ahead of the prop as well as behind
the prop. Besides that we are measuring 3.5 inches of pressure
on the EXIT of the oil cooler when the dynamic pressure is only
four inches of water at that speed. SOMETHING is energizing
that air. The adjacent prop spinning at 5000 RPM a few inches away
is the likely candidate.

We also have further data on another configuration we tried to
support this theory.

Paul Lamar

Al:

I think Paul had used the left tube as reference, but it's actually the
right tube. I analyzed the pictures during lunch and converted the data
to numbers. It all makes sense to me and there is no reverse flow and
there is suction at the exit, not pressure.
Paul will be publishing that soon if not already.

--
Perry Mick
Custom Composite Props
mick@bridgingworlds.com
http://www.ductedfan.com

 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.