Subject: High heat resin
From: ACRE
Date: 7/22/2003, 2:36 PM


Ed Anderson wrote:

 >
I beg to differ on the topic of heat and UV being the only thing
that
will
cause plastic to decay. What about chemical attack? Molded in
stress,
stress
corrosion, moisture contamination, dielectric breakdown. I
design
plastic
parts for a living. I don't know who the hell Arhenius is, but
to me
that
just looks like a standard reaction rate equation applicable to
just
about
all reactions. It is exponential, but where is the intercept? At
zero
Kelvin? What is that little constant k? This is far too general
a
form
of
this equation to be making application specific conclusions.

 SNIP
Beware the Giant equation with many terms of questionable
accuracy
raised to
many powers. Also beware the oversimplified equation. You can
probably
make
this equation work by measuring E, k, and T for a SPECIFIC case.
Do
you
have
good data on what these are for various plastics with various
solvents?
Is
it good within 5%, 10%, 30% for all the solvents or combinations
seen in
an
underhood application,  who knows? What happens when you have a
30%
error
for the value of a constant and place it in an exponential
equation?
Pure
science meets engineering.

Monty


Thanks Monty,

    Always great to hear from someone with both knowledge and
experience
in
a particular area.  From what you related, my polyurethane casting
supporting my throttle body and fuel injectors is undoubtedly doomed
to
a
short life.  I have had a chunk soaking in 100 LL gasoline for over
a
month
now and no deteoriation is evident to visual observation  - i.e. no
crazing
or film build up on the surface.  Probably should stay away from
auto
gasoline with all of its additives.  Again, thanks for the
education.

Ed Anderson

I agree Monty did a great job.
You need to heat that gasoline to about 200 F Ed.
Also there is the issue of: Does the plastic material support
combustion?

Paul Lamar


Paul,

The specs on the plastic indicates it does not readily support
combustion.
I could get it to char and smoke with a propane torch, but it did not
produce a flame or appear to support combustion.  While undoubtedly a
sterner test of the plastic, I think I'll pass on the 200F gasoline in
my
shop{:>). Actually,  with my fuel injectors now setting at the top of
the
tubes, I've noticed that the outside of the tubes now condense moisture
out
of the air apparently due to the cooling effect of evaporating gasoline
in
the tubes. The first time I saw it I though I had a fuel leak from the
"plenum".  Tubes are cool to the touch.

Ed Anderson

That is a HP plus. Good news on the non burning. BTW did you notice any
difference in the fuel burn on your last trip?

Paul Lamar


There seemed to be a lower fuel burn, Paul.  This was my longest (yet)
non-stop from Jackson Mississippi to Charlotte, NC (600 SM) and I arrived
with 7.35 gallons remaining (enough for another hour before dry tanks).  MPG
not too meaningful what with head winds, etc, so hard to know what parmeter
to use.   But at 5400 rpm and 6.75 gph fuel flow at 9500MSL my TAS was 167
MPH.   Turning 5800 rpm with 10.5 gph burn at 8500 msl I had 189 MPH TAS.

I compared that to an almost identical flight a year previous (with old
manifold)  at 9500 MSL and had a fuel burn of 7.75 gph which gave me a TAS
of 169 MPH.  So a gallon per hour less (6.75 vs 7.75)  fuel burn on the
Mississippi trip only knocked 3 mph off the TAS.   A year ago I was turning
5800 rpm with a 10.91 gph burn at 8500 MSL gave me 190 mph TAS on the old
manifold  -compared to 10.5 gph and 189 TAS with this manifold, so only 1
mph less while burning 0.41 gph less.

So while not exactly test quality data it would seem to indicate that I am
getting better fuel efficiency with this intake. Will take a few more
flights and comparsions to tell for certain.  Manifold pressure gage was/is
stuck at 20 psi so hard to peak the tuning {:>).

Ed Anderson
  Will take a few more flights of data gather to really nail it down.

You need one of those $7.95 manifold pressure gages from McMaster Carr :)

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.