> > > > Thanks Monty,
Always great to hear from someone with both knowledge and
experience
in
a particular area. From what you related, my polyurethane casting
supporting my throttle body and fuel injectors is undoubtedly doomed
to
a
short life. I have had a chunk soaking in 100 LL gasoline for over
a
month
now and no deteoriation is evident to visual observation - i.e. no
crazing
or film build up on the surface. Probably should stay away from
auto
gasoline with all of its additives. Again, thanks for the
education.
Ed Anderson
I agree Monty did a great job.
You need to heat that gasoline to about 200 F Ed.
Also there is the issue of: Does the plastic material support
combustion?
Paul Lamar
Ed,
Don't misunderstand me. For your particular case, you may have no
problem.
You are using a two part urethane. These specialty resins can be had in
varieties that will probably work for your particular application. Some
of
these resins are very resistant to chemical attack. A lot of times
Plastics
are the only thing that will hold up in a severely corrosive
environment.
Your manufacturing process is very different as well. You have a very
thick
wall on your parts, something that is not possible for economic reasons
in
an OEM part. You are not going to have a lot of molded in stress because
your resin is a two part room temp cure type of process. Injection
molded
parts are produced by melting resin pellets with pressure and shear in
an
injection press. Then it is shot under very high pressure into the mold.
It
is then cooled using a water jacket in the tool. Economics dictates that
your strive for the shortest "shot time". The flow lines created and the
need to solidify the part so quickly can result in a lot of molded in
stress. The location of these high stress levels is the first place to
suffer under chemical attack. Each plastic is unique in what type of
solvents it is resistant to. The point is under the hood of a car there
is a
very wide range of solvents that may be encountered. Not to mention the
heat. Glass filled nylon 66 is great stuff. And it will last until the
warranty is up at a minimum, but 20 years down the road you are going to
have a pile of rubble. Most people don't keep cars that long and the
manufacturers know this, therefore they don't care if 10 years down the
road
the valve covers crack, warp, or leak. Just like they don't care if the
water pump only lasts 60K miles on average on my Chrysler 318. As long
as
the warranty is up no problem.
In your case you have thick walls, airflow to keep the thing cool, and
what
little amount of surface degradation you might get should not affect the
structural integrity of the part. I also doubt that where the fuel is
being
injected you are seeing temps even as high as ambient, due to fuel
vaporization. Plus the manifold does not sit in gasoline all the time.
You
also used mineral fill which helps somewhat. Plus it is a two part
urethane,
not a production molded part. I think for what you are trying to do,
where
you need to try a lot of different configurations, it makes sense. I
wouldn't expect it to last 30 years under continuous use, but that is
not
what you are trying to do. It works great to prototype and then make a
metal
one once you hit the magic combo, or maybe you can find an appropriate
resin
and make about 5 of them. Just replace them every 3 years or so. That is
the
wonderful thing about silicone molds. You can make about 10-20 parts off
of
the mold. Just keep an eye on it to look for signs that the plastic is
deteriorating. Make it part of your annual. Airplanes are different than
cars. No need to junk the idea. We are after all flying experimental
airplanes right?
Monty
Thanks, Monty for clarifying the situation. Yes, my walls are 1/4" thick
(minimum) and the plastic is not directly exposed to fuel in that the fuel
injectors while they sit in the plastic, their spray pattern is into the
metal tubes. Actually cut a notch in the tube so the stream would all
inject into the tube rather than splash off the wall of the plastic tunnel.
As you noted, the evaporating fuel in the tubes keeps the temps down as
well.
Yes, I am mainly trying to prototype a "final" manifold and the plastic
approach provides more flexibility given the means at my disposal. Also for
approx $26 of resin I can have another "Plastic Plenum" out of the mold.
I think I have one more intake manifold to try and then its on to
turbocharging {:>).
Best Regards
Ed Anderson
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.