snip....
Chuck, in away has done us all a big favor identifying

this

mode

of engine failure. I think we should all send him a
check for what ever we can afford to help him pay of
his

engine over haul. He is going to need a

new rotor

housing and a new rotor for sure. Probably at least
one new

end

housing.

What is your mailing address Chuck?


Paul Lamar

Chris Cosman wrote:

Yeah Chuck, address!
Chris C.
microcosman.com/aircraft

    It's going to take time and money to examine damage and
come up with a fix would like to donate too.
    Let us help you (help us) the rotary engine is evolving,

stuff happens in the process and this seems to be the forum
to

find the answers.  thanks for all the effort everyone, doc
maglaughlin

 Thanks for the offers, but I am in this with eyes wide open,
if

anyone

finds my experience valuable, just consider it a trade for all

the

tips

and valuable knowledge I get from everyone on this list.

Here are a couple of photos of the damage. The center housing
was untouched, the end housing had a small amount of metal
displaced at

the

edge of the inlet port, may be repairable by enlarging the
ports. The rotor and rotor housing are history. It was a new
rotor housing, rotor and end housing was used parts when I
built

this motor. I had about 80 hours on this motor, with Paul's
TES oil O rings looking like new,

will

likely reuse them.

Chuck Dunlap

Chuck have you notified Pineapple Racing about this failure? The
least they could do is help you out with the rebuild.

BTW it far, far better for us to contribute to your engine
rebuilding cost than to the Chuck Dunlap Memorial fund :)

Paul Lamar

"Brian D. Cain" wrote:

Chuck, let me know if you're in need of any hard parts.  I may have
some here that you can use for your rebuild or can find them easily.

Also, great news on the TES oil control ring o-rings; I've been
waiting for a practical, positive review to come

out.

They
should be fully re-usable.

Do you have a picture of the end plate that got nicked near the
intake

port? I'll tell you if it can be removed from porting work or not.

B

Brian D. Cain -/- Grand Prairie, TX -/- bdc196@comcast.com MSN
bdc196@hotmail.com, Yahoo! bdc196, AOL Symajhi, ICQ# 1733105

Chuck wrote:

7/20/03 I emailed Rob Golden at Pineapple Racing a description of the
failure, no response yet. I have already repaired the end housing
damage, it look OK to reuse. The only photo I took was the one
previously uploaded, endhousing_rotor_damage.jpg it shows the damage
pretty well. I have ordered new rotor housing and seals from
Mazdatrix, should arrive next week.
I have always had a spare motor, I can use a rotor from that but I

would

like to come up with another rotor to keep the spare motor parts

intact.

Brian, can you find a 86 NT rotor for me?
Thanks

Chuck Dunlap

Some of us are profoundly upset by your engine failure and near death
experience. It would make us feel better if you would allow us to help
you out with the rebuild.

Paul Lamar

"Near death experience"? This story is getting better and better :-)
It seems to me that I come that close to death every morning as I drive
to work.
Monetary donations will not get me back in the air any faster, It would
make me feel better if people would donate to the Everett Hatch Memorial
fund instead.

Chuck Dunlap

Too late. Check is in the mail. I already donated to the Everett Hatch Memorial fund
as well :)

There is something that is not clear Chuck. Was that motor home coming towards
you? Do you think there was a slight downdraft behind the motor home
causing you to lose a bit more altitude as you just passed over it?
How much did you clear the motor home by?
 
Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.