Subject: [SoCalRXClub] Dyno RX-8
From: ACRE
Date: 8/4/2003, 11:16 AM


We suspect the ECU is programmed with a brake in program
that'll run the
engine rich to protect it.  It should be possible to verify
this with a dyno
run with a wide band O2 attached to monitor AF ratio<<


I expect that Hans is right here, too...I have just about 1000
miles on my
RX8 now, and have been getting some pretty black soot coming out of the
exhaust...coating the inside of the extension tips. Also, occasional
backfiring when backing off from high RPMs over 7-8k.  My
first thought was
unburned gas from an overrich condition, which, as Hans
suggested, could be
a preprogrammed break-in period.

Any way to confirm that this what they've done?, And any idea
how long this
break-in program would be set for?  The manual says to be
careful for the
first 600 miles or so...but there are no special break-in
conditions (except
not to run it at WOT for "extended" periods <G>) and doesn't
mention having
to take it back to the dealer to be "reset"  so, I would think it's a
mileage referenced program, if it exists.

BTW... a word of warning for any of you getting an RX8 ... I
already have
some "finish" damage on mine.  The black "color"  on the door
pillar behind
the window is not paint.  It's like vinyl trim tape! Covers the entire
pillar.

A friend with longer than normal (and worn sharp!) finger
nails closed the
door when I was getting in, and one of his nails caught the
tape and ripped
a little of it...now I have a little v shaped tear in the tape
about a 1/4"
long ... right down to bare aluminum! I tried stretching it back and
smoothing it out, but the wrinkles and stretching make it look
obvious.  See
attached photo.  The other photo is the soot buildup in the
right exhaust
pipe tip.

Harley--

The left exhaust tip is OK Harley? Does not look that rich to me.
It takes a lot of rich to hurt the power. What kind of gas mileage
are you seeing?

Racing Beat has an RX8 engine on the dyno and Jim Mederer did
not mention to
me that he measured it other than 250 HP. I saw it on the dyno myself.

Are you willing to make a balls to the wall acceleration run?
Rev the engine to about 8000 RPM, step off the clutch and time the car
to 60 MPH and/or the 1/4 mile and let us know what numbers you get.
C & D in the 2003 Road Test Annual got 5.9 and 14.5 in the 1/4
respectively.
Pick a good country road as you should be doing about 96 MPH in the 1/4.
If not a measured 1/4 mile just time it to 96 MPH.

Sounds like Mazda/Ford made a big mistake with that vinyl trim tape.
Perhaps you will have to peel it off and paint the panel.
Or make a flat black panel to cover it over.

Paul Lamar

The left exhaust tip is OK Harley?<<

Looks the same, Paul...that picture I included is representative of both.

What kind of gas mileage are you seeing?<<

Actually better than I expected!  The first tank I measured (third thankful)
was a mix of driving...about 30% distance and road driving, and the rest
local.  The fourth tank was all local stuff, with a little bit of interstate
driving, but just a few trips to my son's house...about 12 miles one way.
Both of them calculated out to around 21 mpg.

Are you willing to make a balls to the wall acceleration run?<<

Certainly!

Rev the engine to about 8000 RPM, step off the clutch and time the car to
60 MPH and/or the 1/4 mile and let us know what numbers you get.<<

Did that yesterday in front of my son's house...didn't time it though...just
for fun ... it peaked out at 65mph in second when the limiter kicked
in...I'll do it later today and let you know what I get....

If not a measured 1/4 mile just time it to 96 MPH.<<

It might have to be 95! <G>  That's the peak in third gear, and I'd be a bit
busy shifting, reading the tach and clicking the stop watch to try to catch
it exactly at 96...but, I'll try <G>

a big mistake with that vinyl trim tape ... Or make a flat black panel to
cover it over.<<

Or leave it off and clear coat the aluminum?  Should look OK on my "titanium
gray" car. <G>

Harley

With that kind of gas mileage I doubt it is rich. BTW that is very good
news and bodes well for lower fuel burn in our AC engine applications.

Paul Lamar 

The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.