-clifton j dugan wrote:
I am new to this forum and know nothing about rotary engines other
than
they
don't have as many hand grenade problems. My desire is to have a
high
horsepower power plant for an airboat which has no weight requirements
and
has lots of room for coolers and radiators of large size. I need to
have
a power plant that will put out 750 horsepower with a high reliability
factor and don't care about weight nor space. Gearbox reduction for
propeller needs to be reliable and handle the horsepower but can be
any
size. Airboat people are already using good props that can handle the
horsepower but I haven't seen any rotary engines although I know there
must
be some. It seems like a three rotor with turbo might fit this
requirement.
Several of my friends are using big block chev engines putting out 700
to
900 horsepower but they hand grenade them often.
Any idea about where I might get more info on this subject?
Boy, you guys sure bash this scoop problem pretty well. I know
cooling
is a
serious subject with airplanes.
Clif-
Contact Racing Beat Clif. They have just what you are looking for. 1000
HP.
350 pounds. You will need an old Bell 47 Helicopter gear box for the
prop.
http://www.racingbeat.com/
Paul Lamar
BTW Clif I think you would be better off with two turbo 13B motors.
More prop area for better low speed thrust. Up to 800 HP each on alcohol
and nitrous oxide. Twin airplanes always climb better than singles for
this reason.
Paul Lamar
clifton j dugan wrote:
Twin anything just seems like double trouble to me. I need something
fairly straight forward that runs on pump gas as airboats go in some
unusual
places and gas is hard enough to come by sometimes. I know nitrous and
alcohol are good but hard to re supply in a swamp. I would like to have
enough motor so that the 750 horsepower is conservative instead of on the
edge.
Reliability is still very important in this. Most airboat people use
large
cog belts to gear down the motor to prop speed and are getting good
service
at 800 horsepower. I know that airplane people need something lighter and
more reliable but this is working good on the boats. The belts are
lasting
much longer than the motors. I am looking for something that has the
horsepower with reliability and fairly low maintenance. I know that this
sounds like a dream but the rotary seems like the best possible answer to
me. These standard car motors that are revamped for high horsepower just
have too many parts to break. Even using the latest high tech racing
parts
they just don't last very good, as it looks like the airplane people
already
know.
Clif
clifton j dugan wrote:
For what it's worth.
I had a talk today to my airboat builder and after seeing all the
conversation about cooling radiators of all types, I asked him what he used
and had used in the past. He said that he used the Griffin for a while but
had troubles with it and one other supplier. He uses about 125 to 150
radiators a year in his business. The first thing he said he had trouble
with was the assembly process and the epoxy did not hold up with hard
service. He is now using a radiator made by AFCO racing radiators. He has
been using them for quite some time now with no trouble other than knocking
holes in them by debris flying thru the prop cage. This is the main
trouble with airboats. Very hard service. He does mount them all on soft
rubber. He says there is no epoxy used. All welded. Always to question
these vendors however. Phone 812-897-0900. He also uses oil coolers by a
aftermarket supplier named linco, I believe. He said that these coolers
were made by GM or Harrison and were coolers for big truck transmissions,
bought thru the after market supplier.
I have inquires in with Racing Beat and thanks for the lead.
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.