Subject: Tom Parkes report on OSH trip:
From: ACRE
Date: 8/7/2003, 8:25 AM


Thomas Parkes wrote:

Thanks to everyone for your kind comments.  It was really great flying the
ES to OSH, except for the final 20 miles.  More on that later.  Like many of
you, I would have liked to be parked in the expected "Auto Engine" row.
Unfortunately, only Tracy's RV-4 and a V-6 powered RV-6 were to be found
there.  Was this a breakdown in management planning, or in the all volunteer
parking cadre?  Need to identify the problem and take corrective action for
next year.

I need to correct a few facts and answer some of the questions asked in the
past few days.  First, the maximum speed I've experienced to date has been
195 KTAS (not 200), and that was at 14,000' with a light load.  My turbo is
currently limited to 5 lbs boost (not 10).  Average TAS during the OSH trip
was 170 KTAS at 28" MP and 5400 engine rpm.  We were at gross weight (3200#)
for most takeoffs.  Fuel consumption at cruise averaged 16 gph.

For those interested, my spinner is indeed 16" diameter, and the 76"
diameter IVO Magnum prop is a good performer during takeoff and climb, but
performance definitely falls off at the top end.  I also discovered that its
leading edge tape is suseptable to deformation in heavy rain.  Read on.

My turbo is a large Garrett TE-06, right off of an IO-520.  It is not the
stock automotive turbo.  With a manual wastegate I fully expected to
experience turbo lag and bootstrapping, but neither have occurred.  Instead,
the turbo spools up rapidly on takeoff roll, and once the throttle friction
is locked at 32" MP, the MP remains at 32" right  up to 17,000' without
further throttle adjustments.  Go figure.  My only explanation is that the
turbo has considerable reserve capacity at 5 lbs boost, and I might
experience bootstrapping if the boost were increased to 10 or 14 lbs.  I
don't plan on finding out anytime soon.

I used a combination of mogas and avgas during the OSH trip.  I researched
airports offering mogas (on airnav.com), and even called a few to verify.
Pueblo, CO, showed mogas available, which I verified by phone, but upon
arrival I learned that the line manager wouldn't sell it to aircraft.  So I
bought 20 gallons of 100LL and hopped over to Limon, CO, and filled up on 85
octane mogas.  Unattended field with self-serve gas.  So now I had a mixture
of 91 octane mogas/ 100LL/ 85 octane mogas in the tanks.  Engine didn't seem
to know the difference.

Filled up on 95 octane mogas at Wausau, WI (at $1.90 gal) and just beat a
thunderstorm approaching from the west.  Inbound to OSH I heard that
arrivals to OSH were shut off.  Held short of Ripon for 25 minutes as a
thunderstorm moved in from the west.  When I was finally cleared to proceed
to Ripon, rain showers made the published arrival route almost impossible to
follow.  In and out of heavy showers between Ripon and Fisk, I finally
picked up and followed the east-west road that leads to runway 36L.  I would
not have been able to follow the arrival routing if I hadn't done it before.

After landing, I was directed to the Lancair parking area instead of the
"Auto Engine" row, as I expected.  But the approaching thunderstorm was just
now beginning to hit the field and I couldn't argue the point.  I had to get
tied down.  Consequently, my unpainted "ugly duckling" sat there among the
fancy prize-winning "fast glass" $20,000 paint jobs for three days, where
few would look for it.  Nevertheless, Dave Atkins mentioned my plane in a
couple of his forums and I had a lot of interested visitors--including Paul
Lamar and Mike Cosman.

On the return flight Sunday, I departed about 15 minutes after Tracy.
Stopped in Topeka to help my oldest grandson celebrate his 17th birthday.
Topped off with 91 octane mogas at Manhatten, KS, (good service) and again
at Aztec, NM (octane undetermined).

All in all, the trip was fun and educational.  The 20B purred on like a
champion for 22  hours (which included a family recreational diversion to
Eau Claire, WI).  Maybe I  should have used Temperfoam on the seats.  And,
Paul, I'm glad you added the smiley face following the Christmas prop idea.

Now it is time to look the ES over really close.  I've got to mend the prop
leading edges for sure before flying to Utah next week.

Thanks for everyone's encouragement.  Your day will come.

Tom
"N44AZ flying and loving it in Prescott, AZ."

Jack Beale wrote:

Tom,

    Extremely interesting reading...  Thanks for the post.

    This is the type of installation I'm thinking about.  I'd love to see what you've done...  Do you have some pics or
information posted on a website somewhere...?

    Thanks

Jack Beale
jack.beale"at"att.net

I have a few.  The last picture is an old one but it better shows
the layout of the major parts. I'll send a few more in a few minutes.

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.