Harrison,
Here are some more pictures and illustrations for the light weight
hollow prop shaft that nobody has tried yet. The idea here is to
use the pinion shafts to connect the prop shaft directly to the
rotating planet carrier. This minimize the load path and eliminates
the cost and weight of splines. The same idea is used on the prop
end. The prop drive lugs are welded directly to the flared hollow prop
shaft. These are threaded internally for the prop clamping bolts.
No conventional prop shaft steel flange is used. This in theory cuts
the weight greatly. The prop flange (spacer, back up washer) shown
can be light weight aluminum as there is no load on it.
Since you have an NC mill and you are willing to build your own PSRU
you are the ideal person to try this idea.
I'll send some pictures of the planet gear set shortly so you can get
a feel for how small and light weight it really is.
Paul Lamar
"Burns, Mark" wrote:
Paul;
The idea of a hollow shaft PSRU intrigue me greatly. How thick are the walls
of the shaft? Also, how does the PSRU connect to the crank shaft of the engine? What
is the spacing and the dimensions of the lugs for the prop? As far as the bearings
around the shaft, I was thinking it might be a good idea to have a wheel bearing
like assembly around the prop shaft held in place by a spider mount attached to
an extension of the engine mount. That would hold it very steady.
My brother has a CNC Lathe and a CNC Mill and I was thinking that it might be
better to cut the shaft (lugs and all) out of a piece of steele rather than weld
the lugs to the shaft. I am planning on going to see my brother tonight and I am
going to try to get him to build one. Also, I thought that it might be good to
make the section with the planetary gears as a separate piece (fully enclosed
and lubricated) that can be detached from the prop shaft so that it could be
replaced periodically when the gears begin to wear out. One could produce
the prop shaft for a custom fit for varying lengths for different needs
that different airplanes might have.
Let me know what you think.
Thanks,
Mark
A four inch tube six inches long .125 inches thick would weigh about
about 2.8 pounds. 9.42 cubic inches 6.78 cubic inches or 2 pounds out
of .090. I would try the .125 wall first to be conservative.
As there is combined bending and torque on the tube.
A six inch dia prop flange .25 inch thick weighs about 2 pounds alone.
a six inch long 1.3875 dia (9 cubic inch) shaft weighs about 2.75 pounds
not including the material in the fillet or holes in the flange.
A ball bearing for this shaft would weigh another pound. Total
about 5-1/2 to six pounds. Less if bored out. Tracy does not
recommend metal props for his psru.
Torque 800 foot pound peak (400 ft pounds average) is 800 ft pounds
or 9600 inch pounds.
For torque alone the stress is:
Shear area at .125 wall is 1.6 square inches
so that is 4800 pound shear load at a radius of 2 inches is only about 3,000 psi.
Add to this about 600 ft pounds bending (metal prop, gyro load, 60 degrees
per second pitch rate) and you don't get much stress.
Probably a .090 wall would work fine but I would static test it before I flew it with
a 800 foot pounds of torque and 600 ft pounds bending by bolting on a 2 by 8
beam simulating a prop and hang a bunch of weight on the end of the 2 by 8.
Mount the finished PSRU at about a 70-80 degree angle with a 4 foot 2 by 8 and
hang 200-300 pounds on the end. That ought to do it :)
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.