Subject: VAZ/Lada Wankel life
From: ACRE
Date: 8/30/2003, 2:42 PM


The bottom of the first  web page on this airplane says that
it will use
two "vankel" type engines made by Vaz in russia.Then it goes
on to say
that it will use continental engines. Anybody know what
engines they are
intending to use on this plane?
Brian Trubee

Continentals in the US because they are certified. Vaz/Lada
Wankels in
Russia
because they are better :)


http://digilander.libero.it/cuoccimix/ENGLISH-automotorusse4(lada2).htm

Ford/Mazda needs to wake up and FAA certify the RX8 engine for
use in
aircraft.
We have already showed them how to do it including use of their
own
transmission
parts in the psru.

I would be glad to help them in any way I could.

BTW for all you one rotor fans. How many are interested in
buying a Russian
one rotor? I am thinking of hopping on a flight to Russia and
contacting the
factory.

Paul Lamar

Be intesting to know how many Mazda parts fit/ are
interchangeable? They are
pretty good at sticking to the original design.

Márk Wrathall.


As a word of caution, the following statement is copied from the web
site:
Rolf Pfeiffer

"But the life of the Lada-Wankel engines is terribly short: 20.000
km!! This
because the Russian alloy is of poor quality: a Wankel engine needs
high-quality
materials for the various elements. Making an engine of this type with
the Russian
steels, it's like producing an aeromotive engine with the bronze of
the antique
coins...These engines are very interesting, but the lacks of money and
resources
makes the ideas of the Russians engineers hard to translate in the
reality. Still
today, these engines are produced in limited series (also for the
aeronautical
use), and used, for example, on the new Lada "110 Super Tourism" (two
pics above),
equipped with a two-rotor engine, for the National championships."

That was then! Russians can now buy steel and other metals from anywhere
in the world.
Sounds like anti communist propaganda. I flat don't believe it.
Their fighter aircraft and rockets are second to none.

Paul Lamar


Richard Konnen wrote:

I have to chime in. I am by no means an expert on alloys or Wankel
engines.
In the model engine market the Russions seem to have some of the best
competition control line engines, and its because of the alloy of metals
they use, aluminum piston, brass or aluminum, chromed sleeve.
Richard Konnen


I agree. I donīt know now, but for a long time the Russians where also world
leading in welding technology and metalurgy in general. In school we got
explained that is because in the old soviet system research was done in any
area until there was nothing left to research, if it was necessary for the
present level of technology or economy or not. In the western world in
contrast, research was mostly done on some kind of economic basis and then
only to a depth that was required for a certain project on hand "... until
here and no further!" - money rules.
However in the eastern block, this way there was a lot of knowledge on
standby to be applied after a  short development time as all the basic
research was already there.

On a similar note compare the new Bombardier aircraft engines with the LOM
aircraft engines. The LOMīs a roughly 40 years old in their present stage,
but they constantly update them. Donīt need carbheat, have selective
supercharger, altitude compensating fuel injection - no mic control needed,
aluminium alloy con rods, run on any gasoline you find, aircooled and here
is the hammer: they are still at least 50lbs lighter than the new breed! At
the nearly same specific fuel consumption!

Who ever wrote the report on that russian engines, probably did not know a
whole lot of the inside workings of russian production...

Thomas J.


 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.