> > > > > > Hi Bill
Yes, current ducts are working just fine in the cooling
department.
However, I felt that the duct shape was probably causing
"eddies"
around the
inside of the opening and disrupting some air flow/cooling.
Plus
the
current openings are 24 square Inches for each radiator. I
thought
that if
the smoother transistion from duct to radiator improved the air
flow
into
the duct then perhaps I could reducing the opening. However,
Paul,
may be
correct about my old duct cooling better as I reduced the
opening
from 25
in^2 to approx 10in^2 on the new duct. Perhaps a bit overly
zealous
{:>).
If the new duct does cool as well as the old duct, then I
believe I
will
have reduced some of the cooling drag, if not, then I rip out
the
foam and
go back to the old duct. Hope to make first flight tomorrow and
will let
everyone know of the results.
Ed Anderson
Don't rip ALL the foam out, just enough to go back to the 25 sq.in.
and
do that
in steps. You may very well get some benefit from the reshaping,
even if
you can't go all the way to 10 sq.in.
Bill Schertz
KIS Cruiser # 4045
Good Point, Bill. Incomplete success doesn't necessarily mean total
failure
{:>)
Ed Anderson
Ok folks, made the first flight today with my reduced/reshaped radiator
inlet for the left evaporator core. The right evaporator core was left
unmodified to provide a safety net sufficient to do the pattern and land if
take off temps exceeded expectations. Fortunately, that was not necessary.
OAT on first take off was a humid 85 degrees. No temperature increased
noted during ground run up, so launched and made max rate of climb, not
seeing any abnormal temp increase I left the pattern and continue Max rate
climb to 4500 MSL. Max temp of coolant during climb was 210F (normal for
max rate climb at these OAT temps is 205F), Max oil temp was 200F nominal
for max power climb. Max temps were reached about 2/3 of the way through the
climb.
In level flight, my coolant temperatures normally run 5 degrees colder than
my oil temp. Today my coolant and oil temps were the same. So average
coolant temp was increased by 5 Degrees F. Total radiator inlet duct area
was decreased from 48 square inches to 33 square inches. 24 Square inches
for the right inlet duct and 9 square inch inlet for the modified right
duct. Probably some drag benefit, but did not try to investigate that
aspect.
I flew to an airfield 50 miles away to have my transponder recertified and
when I launched out of it, the OAT (ground level) was 92F
After level off I ran at different power settings to see the effect.
5800 rpm burning 11.9 GPH at 4500 MSL with OAT at 78F My oil and coolant
were both 190F.
5400 rpm burning 9.6 GPH at 4500 MSL with OAT 80F My Oil and coolant were
both 185F
5200 (My normal cruise rpm) burning 7.25 GPH at 4500 MSL with OAT 80F My
oil and coolant were both 180F
In summary, the 33 % reduction in total radiator inlet area appeared to
have increased coolant temps by an average of 5 Deg above the normal (the
old duct). It could be that both the remaining radiator and perhaps the oil
cooler are rejecting any additonal load with no problem.
It appears that smoothing out the path for the air from inlet to radiator
surface has benefited the cooling situation. It could be that additional
heat may be rejected by the right (second in series) radiator as the coolant
it received from the left radiator was probably now a bit hotter. I also
observed that the plate of the PSRU covers an area 3 " in from top to bottom
of the rear of each radiator and the plate is only 2" from the rear of the
fins at its closest, so that is obviously not helping flow, the Ross Bell
housing did not, so a bell housing might improve flow conditions .
I strongly suspect I would probably find that a similar reduction of the
right radiator inlet duct to 9 square inches would see my coolant (and
probably oil) temps increase considerable more than another 5 F. OAT at
ground level was 94F when I landed, so not the hottest of days, but not the
type I normally prefer to fly in.
>From what I have seen so far, I think it worth pursuing a reduction with the
right radiator duct. I will probably not reduce it as much for the reason
mentioned above. With some other things to take care of, probably won't get
to it until later part of Sept at the earliest. But, I have no problem
flying with current asymmetrical ducts, so will leave it as is for the time
being and collect some more data.
It it appears that some cooling benefit is derived from providing a smoother
transition from duct to radiator (even if far from a perfect implementation
of the K&M approach) than my old duct provided.
Oh, yes, as an aside, its been 25 hours since I replaced the spark plugs and
right on schedule - on the way back, I got the first SAG (Sparkplug
Attention Getter) indication. So it appears 25 hours on 100LL about the
average time for replacing plugs in my case. I finally got a spark plug
cleaner, so need to clean a set (as the electrods do not appear worn) and
see if getting the lead off the ceramic cone helps any.
Best Regards
Ed Anderson
Ed please don't do anything until you get that cooling temp measuring system working.
We will learn a lot more about your system when that is working.
Great data. Thanks.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.