Dean Head wrote:
Joe Hull,
Glad to see another Cozy builder leaning toward a
rotary.>>>>> Dean Head
Cozy MK4 #1040
"Joe Hull (Pilgrim Technologies)" wrote:
I'm more than leaning - I'm completely tipped over! I
installed
my
rotary engine mount from Conversion Concepts a couple
days ago
and
pickup my rebuilt 13B in a couple days!
Still have to work out all the plumbing in and out!
Thanx,
Joe Hull
Cozy MkIV #991 - Strakes in process (as well as engine)
Paul,
In early August you suggested Paul Conner send his
SQ2000>> motor mount back,
suggesting it was going to fail. That engine mount looks
like a>> Conversion
Concepts mount. Care to elaborate?
Dave Wilenius
Cozy Mk4 #796
Conversion Concepts changes their design with regularity.
I have
not
seen the latest. If Joe Hull sends me a picture I will
comment.>>
Paul Lamar
Well Joe, how about it? I would think that the canard
community
would
be very much interested in this.
Dave Wilenius
Cozy Mk4 #796
You can see lots of photos on the web site:
www.conversionconcepts.com
Bulent
OK I will assume these are the latest.
Paul Lamar
First problem.
This problem jumped out at me when I just accessed the web site.
When they calculated the CG by NOT including the 8# starter and
the 30#
prop
the CG on the engine is further forward (pusher) than it is in a
real installation. This erroneously made the the four mount system
that they use look better than it really is. Very clever or dumb
depending on how much credence to their motivation you give them.
The real engine CG is further aft in a pusher installation. About
where the rear housing is located. Honest mistake? Perhaps!
Paul Lamar
One other point of interest, it that there is also no alternator or
belts on the opposite end of the engine (opposite the starter and
prop). I would suspect that putting the alternator and belts on,
that might help to partially offset the weight ot the starter? Of
course, it's hard to figure prop, as there are so many variations.
Just an observation. Paul Conner
The 30 pound prop weight will have the major affect as it's CG is at
least 14 inches aft of the rear end housing and about 20 inches aft of
the center of the engine. The eight pound alternator CG is probably
only five or six inches forward of the center of the engine. The
starter will have a larger effect than the alternator.
Paul Lamar
Are you guys looking at the same web site I am? I don't see that they
are claiming the CG is at the point shown. There is a link to a
picture and formula so that you can add you own components and figure
the w/b for your installation. Add your prop, starter, alternator,
exhaust system, etc. Then you get the w/b for the total package.
I'm not saying anything about the appropriateness of their motor mount
design, just that they aren't claiming the cg is 23"
Bob White
-
http://www.bob-white.com
N93BD - Rotary Powered BD-4
Look closely at the picture. The engine is balanced on that piece of
wood. They don't say so but a picture is worth......
Also the picture file name has the word "Actual" in it.
Clever, purposely misleading or just a coincidence?
Paul Lamar
"Pictured is our dirty 13B engine for our RV-6, soon to be rebuilt, we
thought we would bolt up the redrive to check the fit of some things and
get an actual weight and CG location with the redrive installed. We came
up with a simple weight and balance formula you can use to check the
engine CG with different propellers and accessories, intake manifolds,
exhaust systems, ect. Go There."
Here is the paragraph. It says they have the actual weight and CG of
the engine and redrive. It says go use their formula to get the CG with
prop and accessories added. Where do you see anything misleading!
Bob White
http://www.bob-white.com
N93BD - Rotary Powered BD-4
The picture itself is misleading. Also the use of four equal sized
rubber mounts on each end of the engine is also misleading.
That would lead one to conclude the engine/psru/prop CG is in
the middle of the engine. Since the real engine/psru/prop CG is
about where the aft mounts are located there is no need for
the front mounts.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.