Subject: meziere wp 430
From: ACRE
Date: 9/16/2003, 10:58 AM


Barnhart wrote:

Paul,

Just finished talking with Jay at Meziere.  The inlet is on the
right
as shown on page 17 of their e catalog
http://www.meziere.com/. The hose fitting that it is showing
on the inlet can be removed and replaced with an AN fitting up to
AN 24. It does have a dual outlet capability with the option
of one being blanked off. The outlets can be positioned in 45
degree increments to the inlet.

Plan on having the outlet facing the adapter on the front
accessory case.  Outlet a straight shot also to keep head
pressure and
hp required to run it down.

 Forgot to ask him about a source of pulleys tho.....

Barny
MGDQ 20bt

AN24 is inch and a half. Stiff and heavy :)

How big are the outlets?

So what do they get for that pump Barny?
What will pulleys cost?

There still is a sharp 90 degree turn for the water going in.

Paul Lamar

Paul,

Pump costs about $350.  Will be cooling 300 hp, better too large
than too
small. Starting to get a nagging in my head on how to cool this 20bt
efficiently from -10 to 100 degrees.  Murphys law is on the side of
overheating.

Pulleys.  No idea, but odds are the first one won't be the right one.

Outlets are up to AN 24 in size.

Hoping to beat the 90 degree corner with layout. If not the
smallest angle
possible.

Barny
MGDQ 20bt


I am talking about the sharp 90 degree inside the pump Barny.
It is identical to the stock Mazda pump in that regard.
There is nothing you can do about it and it is one of the reasons
I went to all the trouble of making a new casting for the Mazda cartridge.

That wp 430 was designed to bolt to the front of a Chevy block.
Most if not all stand alone centrifugal pumps have a straight shot
into the center of the impeller. That is the most efficient
configuration

Paul Lamar


Paul,
Concerning that 90 degree turn in the w/p housing, I welded in a
curved piece that turns the sharp 90 degree turn into a sweeping bend.
Its not perfect, but looks like it will help quite a bit.  Time will tell
how much.
With my own TIG welder and a little skill, it seemed like a low budget fix.
Sorry, no pictures.
Mark S.

Mark S.


Did you cut a hole in the case to do this? I don't think you understand
what I am talking about. The hole in the case would have to
be exactly where the shaft is.

The lower picture shows just the Mezier cartridge and impeller.

In the Mezier configuration the impeller driven from the water inlet side
or front side of the impeller. There is no other way and no fix. The
Mazda impeller is driven from the back side of the impeller! The
water comes into the impeller stright in and unimpeded in my version
and through a sharp 90 degree turn in the stock version. Both are
fundamentally different and better than the Mezier pump configuration.

Paul Lamar


Looks like we're talking about two different issues.  My mod addressed the
sharp 90 degree left turn just before the coolant enters the block.  This
would be at the
far right side of your last picture.  My mod didn't address the water
entering the
pump.  Your design is surely a big improvement there.

Mark S.



This Meziere pump will work but the question is how well with one 
output blocked off.

The KSE is a better choice as the impeller is driven from the back side.
It is possible to feed the water straight in as the older KSE version
did just that. You still must deal with the dual outputs and lack
of adequate shaft bearings for a belt drive.

Perhaps we can find someone to make a 20B billet pump housing with a single
output using the Chrysler Mopar cartridge. It is a pretty simple job
for an NC mill.

We are assuming of course the stock 13B pump is inadequate but
that has yet to be proven. Tom Parkes turbo 20B powered airplane is not cooling 
perfectly yet but that could be due to other aerodynamic problems of scoop,
duct and rad air outlet and not necessarily the water pump.

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.