> > > > > >>>>> Dean Head wrote:
> > > > > >>>>>>
> > > > > >>>>>> Joe Hull,
> > > > > >>>>>> Glad to see another Cozy builder leaning toward a rotary.
> > > > > >>>>>> Dean Head
> > > > > >>>>>> Cozy MK4 #1040
> > > > > >>>>
> > > > > >>>> "Joe Hull (Pilgrim Technologies)" wrote:
> > > > > >>>>>
> > > > > >>>>> I'm more than leaning - I'm completely tipped over! I
> > > > > >installed
> > my
> > > > > >>>>> rotary engine mount from Conversion Concepts a couple days
> > > > > >ago
> > and
> > > > > >>>>> pickup my rebuilt 13B in a couple days!
> > > > > >>>>>
> > > > > >>>>> Still have to work out all the plumbing in and out!
> > > > > >>>>>
> > > > > >>>>> Thanx,
> > > > > >>>>> Joe Hull
> > > > > >>>>> Cozy MkIV #991 - Strakes in process (as well as engine)
> > > > > >>>>
> > > > > >>>> Paul,
> > > > > >>>>
> > > > > >>>> In early August you suggested Paul Conner send his SQ2000
> > > > > >>> motor mount back,
> > > > > >>>> suggesting it was going to fail. That engine mount looks
> > > > > >like a>> Conversion
> > > > > >>>> Concepts mount. Care to elaborate?
> > > > > >>>>
> > > > > >>>> Dave Wilenius
> > > > > >>>> Cozy Mk4 #796
> > > > > >
> > > > > >
> > > > > >>> Conversion Concepts changes their design with regularity. I
> > > > > >have
> > not
> > > > > >>> seen the latest. If Joe Hull sends me a picture I will
> > > > > >comment.>>
> > > > > >>> Paul Lamar
> > > > > >
> > > > > >
> > > > > >> Well Joe, how about it? I would think that the canard
> > > > > >community
> > would
> > > > > >> be very much interested in this.
> > > > > >>
> > > > > >> Dave Wilenius
> > > > > >> Cozy Mk4 #796
> > > >
> > > > > You can see lots of photos on the web site:
> > > > > www.conversionconcepts.com
> > > > >
> > > > > Bulent
>
> > > > OK I will assume these are the latest.
> > > >
> > > > Paul Lamar
>
> > > First problem.
> > > This problem jumped out at me when I just accessed the web site.
> > >
> > > When they calculated the CG by NOT including the 8# starter and the
> > > 30#
> > prop
> > > the CG on the engine is further forward (pusher) than it is in a
> > > real installation. This erroneously made the the four mount system
> > > that they use look better than it really is. Very clever or dumb
> > > depending on how much credence to t heir motivation you give them.
> > > The real engine CG is further aft in a pusher installation. About
> > > where the rear housing is located. Honest mistake? Perhaps!
> > >
> > > Paul Lamar
>
> > One other point of interest, it that there is also no alternator or
> > belts on the opposite end of the engine (opposite the starter and
> > prop). I would suspect that putting the alternator and belts on, that
> > might help to partially offset the weight ot the starter? Of course,
> > it's hard to figure prop, as there are so many variations. Just an
> > observation. Paul Conner
>
> The 30 pound prop weight will have the major affect as it's CG is at
> least 14 inches aft of the rear end housing and about 20 inches aft of
> the center of the engine. The eight pound alternator CG is probably only
> five or six inches forward of the center of the engine. The starter will
> have a larger effect than the alternator.
>
> Paul Lamar
> Are you guys looking at the same web site I am? I don't see that they
> are claiming the CG is at the point shown. There is a link to a
> picture and formula so that you can add you own components and figure
> the w/b for your installation. Add your prop, starter, alternator,
> exhaust system, etc. Then you get the w/b for the total package.
>
> I'm not saying anything about the appropriateness of their motor mount
> design, just that they aren't claiming the cg is 23"
>
> Bob White
-
> http://www.bob-white.com
> N93BD - Rotary Powered BD-4
Look closely at the picture. The engine is balanced on that piece of wood.
They don't say so but a picture is worth......
Also the picture file name has the word "Actual" in it.
Clever, purposely misleading or just a coincidence?
Paul Lamar
Despite any possibility of a filename being misleading, I found this picture
to be useful. What I saw was not an
implication of a final cg, but rather the cg of what was shown
in the picture. The picture very clearly does not
include the prop and I would not have expected the w/b to be
the same with additional equipment added. The picture
gives me an idea within about 1-3/4 inches where a datum is
that I can apply the moments of anything else that I add.
I think that is close enough to apply design loads for the
mount. Of course before flight the entire airplane needs
to have the w/b computed.
Correct me if I am wrong, but don't you want to have the cg
closer to the prop end and the location of the main rubber bushings?
Dick Gregory
The engine/psru/prop CG is where it is. There is nothing you can do about
it. The datum for the calculations of the CG of the engine can be anywhere.
In an airplane CG calculation it is usually up near the prop flange. In
an engine situation it could be the front edge of the e-shaft pulley.
Let me put the whole thing in perspective. If the guy doing the designing
really knew what he was doing he would not compromise the motor mount
and use four equal sized rubber bushing at the four corners the engine
oil pan. The rear two rubber bushings are carrying 90% of the load.
He would use two larger rubber bushing under the engine/psru/prop
CG!
He also would not start with a chunk of aluminum that was 18 by 14
by 3/4 of an inch thick. The weight of that chunk of aluminum alone is
19 pounds! At $3 a pound that is about $60 worth of aluminum. You are
paying for that and then some.
To machine it on an NC mill to cut the weight by half or 2/3 rd would
cost several hundred dollars. You are also paying for that. When
you are done the plate is going to weigh somewhere between six
and eight pounds.
Four or six pounds of that weight is totally unnecessary since
it supports the two front rubber bushing that carry little or no load.
A Schertz beam would be one tenth or less of the cost and weight.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.