I was stripping down my 1988 turbo throttle body for use
on the dyno engine and I came on two sets of dual butterflies
one after the other. Does anybody know why Mazda did this?
There is one large one and two sets of dual in the other
two throats. News to me.
Paul Lamar
Hi Paul,
yep! found them in every one of the three throttle bodies I have -
up to
and
including the 1990. My understanding is that they are there to
prevent
airflow into the secondaries until there is sufficient airflow/rpm?
into
the
engine. If you stomped on the throttle at very low rpm the second
set
of
butterfly plates (one further in toward the engine) can be made to
open
via
their physical linkage to the throttle shaft. If rpm is too low
when
you
stomp on the throttle this opening of the secondaries could cause
engine
performance to suffer/stumble. The control system will not permit
the
first butterflys in the air flow stream to open until the control
conditions
criteria (what ever it is) is met even if the second set (are opened
by
the
linkage). That is what I have been told. Sounded plauseable to me.
Best Regards
Ed Anderson
Well I took them out and found out the shaft was very useful.
More on that later.
It was real hard to break those four little screws loose. I wound
up using a Dremal tool to grind down the sides of the screw
heads so I could get a small vice grip on them. I guess Mazda
did not want them coming loose and going through the engine.
There are three stock 1.78" ID throats with a total area of 7.2
square inches. A single throat of the same area would have
less pressure loss.
Using the shaft that came out of it... it is possible to
build a light weight single throat TB with a 3.5 inch ID or 9.6
square inches. Much like you and Chuck did. That shaft would be
hard to fab if I had to make one. I'll do that some time in
the future.
A single throat of the same area would have less pressure loss.
A bigger one even less. I'll measure the stock pressure loss
on the dyno using just the dual and then the dual and the single.
It makes no sense what so ever to have any TB pressure loss in
an engine that runs WOT 90% of the time. Pressure loss equals HP
loss.
Furthermore after getting everything off I could... the stock TB
still weighed three pounds!
BTW I arranged the linkage so the single and the dual butterflies
open at the same time.
Paul Lamar
Yes, I found the same use for the butterfly shaft. It will support a
throttle plate that will fit inside a 4" diameter (1/8" wall) aluminum
pipe
just nicely. I had some laying that size tubing laying around and
drilled a
shaft hole through the sides and then fashioned a throttle body plate
(the
hardest part) out of some sheet aluminum just to test it out. Then
found
the 75mm throttle body for cheap and stopped work on it.
On the Mazda TB I also rigged the "real" secondary butterfly to open
with
the primary. I also found that their was some play designed into the
factory
linkage that gives the butterfly some free play near the full open
position. In other words, the stock linkage would not force the
butterfly
fully open but somewhere close to say 90-95% - don't have a clue as to
what
purpose that serves. But, I wanted the secondaries full open when the
primary was so I rearranged that linkage as well.
I used one of the various surplus springs to rig the throttle shaft so
that if the cable should break/become unattached the throttle plate
spring
open rather than shut.
Yes, its is a heavy beast even with all the non-essentials removed. The
one
I used on my second manifold appeared to work well but undoubtedly had
more
air resistance than a single TB with the same open area.
Using the single 75mm throttle body on the third manifold, the only
thing I
have noticed different about it (than the stock TB) is that if you push
it
open very rapidly - the engine will hesitate until the fuel catches with
the
new situation. But that may also be due to having all 4 injectors in
the
throttle body mount - having a pair closer to the intake might eliminate
that hesitation. Otherwise, I seem to have a tiny bit less pumping loss
looking at manifold pressure at certain rpms.
Ed Anderson
I forgot Ed. What is the one on the right? The injector stumble is well
known with upstream injectors but supposedly they give slightly
lower fuel burn at the same power due to better mixing. My 182
will stumble if I jam the throttle open.
Paul Lamar
I agree, Paul. Not saying that the stumble is sole responsibility of the
larger throttle body, it may indeed only be due to the upstream injectors.
Trouble with changing more than one thing {:>)
The one on the right in the second photo is the smaller 65mm Chevy throttle
body I picked up for $15 then found the 74mm one currently installed. The
first photo is my experimenting with the 4" dia pipe and the Mazda butterfly
shaft. Your are looking at the rear where I had intended to braze a flat
mounting plate. I had already turned a small lip on the front end to retain
the hose clamp. But that is as far as I got. I was also thinking about
installing some of the oil impregnated bronze (can't recall its name) rods
(drilled for the shaft size) into the pipe as bearings.
Ed Anderson
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.