With all the muffler ideas out there like the tuned tangential
muffler,
the simple tangential muffler, the VAM and the turbo charger I have
slowly come to the conclusions that this is the only way to build a
motor
mount. You need as much clearance around the exhaust side of the
engine
as you can get and this is the best way of doing it. I call it the
beam
mount. The beam and the upper diagonal brace must lie in the same
plain. It must also be laterally braced under the oil pan.
Paul Lamar<<
Al Gietzen wrote:
Looks sort of like my mount.
Al
Yes it appears similar but this mount violates a few rules of the beam
mount which leads to indeterminant (not easily calculated short of a
finite
element analysis) local bending loads in the tubes. Tubes A, B, C, D and
E
all need to be in the same plain. The joint where tubes A, B, C and E
come together
should be moved forward closer to the front motor mount beam. Not
entirely
necessary as there is very little load on the front motor mount as the
CG of the engine/PSRU/prop is much closer to the rear mount.
Cantilevering
tube E forward to take these loads as done here is workable. Also tube D
is in the
wrong position leading to unnecessary bending loads in tubes E and C.
Also this mount needs to be diagonally braced laterally under the engine
or over
to the spar from one or more sides. Currently tube bending stiffness is
relied on to do this job.
I would monitor this mount on a regular basis for cracks.
Paul Lamar
-----------------
Good points, and I'd only disagree on the CG being "much" closer to the
rear mount. Based on how the full-up engine/redrive balances on a chain
on the hoist, I estimate the CG within an inch back of being centered
between the mount bushings. This is without the wood prop and prop
extension.
Also I'm not sure about the need for diagonal bracing; the way in which
the tubing is 'out-of-plain', and with the added gusset make it strong
sideways, and torsionally quite rigid.
But I have no detailed stress analysis on this mount and will monitor it
closely. A broken engine mount could really ruin your day. It works
fine for the 220hp Franklin for which it was designed.
Al
Have you given it the six G hard landing static test? If your engine weight
is 400 pounds six G's would be 2400 pounds. Assuming for the moment
the engine/psru/prop CG is in the center of all four mounts that
is 600 pounds down force on each rubber bushing. Not counting torque
reaction. I know you know this but we have a lot of new guys on here.
Possible it will be OK. Some of those old mount designs violate all the
rules. Due to years of experience and AD's & repairs along the way with various
doublers and gussets they eventually become very reliable. My C 182 mount
is a good example. Plenty of short sections of doubled up tubing and gussets.
These eventually add the required local bending strength to delay the onset of
fatigue cracks indefinitely.
One can remove a lot of uncertainty by never putting a tube in bending.
In other words by designing the motor mount as a pure pin jointed space frame.
I find that CG position hard to understand as the PSRU is 45 pounds behind
the rear mount and the bare 20B is 260 pounds. Also your front mount appears to
be several inches ahead of the front cover. Do you have a cast iron water pump
housing on there? :) Well I guess the alternator could tip the balance forward.
The CG of my 13B with alternator, starter and Tracy PSRU is very near
the back (as in the car) end housing. The prop will put it right
at the end housing.
Do you have the starter on there Al. Most wood props are about 30 pounds.
If the PSRU is 15 inches long and the CG is in the about middle of the engine
(12") the moment due to the prop alone would be about 700 to 800 inch pounds.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.