Subject: Turbo on non-turbo
From: ACRE
Date: 2/2/2004, 9:16 PM


     Yes if turboing a non turbo engine. The big problem with
experimenting
     along these lines is one or two detonations can fracture the three
piece
     2 mm apex seals. That in turn can destroy and expensive rotor
housing. If you
     are going to do this kind of experimenting change the apex seals to
     the 2 piece 3 mm variety. This means the rotor slots must be ground
     out from 2 mm to 3 mm. There is a good possibility the new RX8
style 2 mm
     2 piece apex seals now available for the 13B from Mazda will also
     solve this problem but so far we have had no feed back from the
field.

     Unfortunately the three piece seals turned out to be a disaster
     for the turbo engines with anything more than the stock boost
     and a perfectly working fuel injection system. If a fuel pump
     or injector failed or some other problem causing the mixture
     to go lean the engine would detonate and fracture the stock
     2 mm three piece seals.

     Paul Lamar


I've got a stock 13BREW that I intend to run normally aspirated, but I'm
setting up the engine compartment in such a way that I could conceivably put
a turbo in in the future. I've got space between the engine and the firewall
up high, just aft of the water pump. Hard to imagine that I would (Since I
will be so busy building the scale P-38) but what is considered a good turbo
to use for this engine?

Don't get excited about the P-38- I'm just kidding.

Brian Trubee


You could use the 90-91 turbo.

Paul Lamar

"Brian D. Cain" wrote:

I recommend looking into the BorgWarner/Schwitzer S200 line.  They're
designed
as a T04 replacement turbocharger for light to medium-duty diesel trucks
that run
gobs of boost pressure for extended periods of time.  I have a chart of the
S200
series' compressor maps here printed out but not scanned in.  We stumbled
across
them on accident when we were looking for an upgraded turbocharger for a
buddy
of mine's street car.  This unit turned out to be a much better choice over
the
commonly available Turbonetics' types.  It generated manifold pressure
*much*
more quickly than an equivalent T04-type and was very efficient.
Comparably,
it produced more power (on the magnitude of about 15% or so) over an
equivalent
sized T04 and "hit" harder and earlier in the RPM band.

The great thing about these turbochargers is they're cheap: about $400 to
$500
brand-new.  Plus, they come with divided turbine housings with a divided T4
exhaust flange for the exhaust manifold.  If one could design a
tuned-length, fully
divided exhaust manifold for this, they'd have a heck of a setup with
reliable power
well into the mid to high 300bhp range on a 13BT.

Here's a couple of large pictures of it to give you an idea of its size:

http://bdc.cyberosity.com/pictures/HassanMalik/P1010044.JPG
http://bdc.cyberosity.com/pictures/HassanMalik/P1010046.JPG

B
__________________
Brian D. Cain -/- Grand Prairie, TX -/- bdc196@killspam.comcast.net
bdc@killspam.teamfc3s.org
BDC Motorsports - Performance Rx-7 13B Rebuilds, EFI tuning, etc.
MSN bdc196@killspam.hotmail.com, Yahoo! bdc196, AOL Symajhi, ICQ# 1733105
http://bdc.cyberosity.com -/- http://groups.yahoo.com/group/HaltechSupport-- 

The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.