Whoa!!!
All engines are, as we know, a balance of engineering compromises. The compromises can be skewed one way or another depending on the application requirements.
One of the compromises in rotary engine design is metal temperature of the rotor housing in a small region near top dead center (actually a little past top dead center). This is the region of the engine that has the highest heat flux from the combustion gas, through the metal, and into the coolant. For an aluminum rotor housing (steel liner or not) material properties quickly deteriorate above about 400 F. And that is for a rather exotic aluminum alloy. Mazda's die-cast alloy is probably not that good. Combine the reduced material properties with the thermal expansion, and you have a recipe for crushed rotor housings if the metal temperature is not carefully controlled. If you look in the Mazda service manual, the critical rotor housing measurements are all centralized in that high heat flux region.
The localized rotor housing heat flux is higher than in a piston engine for a few reasons... one, that area is never cooled by in incoming intake charge like a piston engine (even a two stroke piston engine); two, the gas velocities past the rotor housing minor axis are much higher than the relatively quiescent gas velocities in a piston engine. As I recall, the only "common" mechanism with comparable heat flux to a rotary engine is a nuclear reactor.
Anything that reduces the heat flux will raise the metal temperature. When operating at high power, the cooling mechanism in the high heat flux region is believed to be predominantly nucleate boiling. (Nucleate boiling has been discussed here before, I'm not going to go through the whole dissertation, but it is important to recognize that it is far different from film or bulk boiling. Nucleate boiling is an exceptionally efficient heat transfer regime, where film boiling and bulk boiling will DECREASE the heat flux and cause rapid engine failure.)
Changing the coolant to a medium with a higher boiling point will lower the heat flux and consequently raise the metal temperature. The temperature rise will be approximately one degree for every degree of increase in the boiling point (assuming that the engine is being operated at high output). Then, once nucleate boiling begins, the boiling thermal properties of the fluid will become important... it is very, very likely that ethylene glycol's properties are inferior to water or a water - glycol mixture.
Boiling (film or bulk) should NOT be a problem with a properly designed cooling system. Unless truly ridiculous power is attempted, the standard Mazda system works pretty well. There are certainly some "tweaks" that are pretty well known to give it a little additional margin.
I agree that improved lubricants and elastomers will push the thermal limitations of the engine higher in some areas, but there is still the fundamental problem of aluminum's deteriorating properties at modestly elevated temperatures, and that is compounded by the basic design of the Mazda engine where the clamping forces will inhibit the expansion of the rotor housing until plastic deformation occurs -- and this happens at relatively low bulk coolant temperatures -- perhaps 285 F or so (a guess, only). Every rotary engine builder has a graveyard of crushed rotor housings.
Finally, one more problem, less significant... Spark plug cooling. Rotary engine spark plugs have a tough life. Increasing the coolant temperature by an appreciable amount will have a detrimental effect on plug life. If the coolant temperature is raised enough, it may not even be possible to find a cold enough spark plug to avoid detonation caused by the temperature of the plug tip itself. It's also got to be a hot enough plug to start a cold engine and operate it at low power also. Detonation from a hot plus is a separate issue from intake charge temperature.
Sorry to throw a damper on it, but I think water-glycol at 50-50 is about the best coolant we are likely to find for applications that require reliability and durability.
Jon Lauter
Rotary Power Marine Corporation
Very good article Jon. The fact is we don't know any of this for sure. The reason is
the sustained temp in the engine is limited by the boiling phenomena. Sure the temp shoots up for a short period of time and then the engine is shut off. It most certainly will melt if the engine is continued to run with no coolant.
The metal temp in the rotor housing may not be directly proportional to water temp in the range of 220 F to 250 F as Continental found out. Unless we instrument the rotor housing and raise the water temp we will never know for sure.
In the past few years we have heard very little about rotor housing crushing. The crushed area was very localized. It appears that the crushing phenomenon had more to do with whether the O-rings slots were in the rotor housing or the end housing. Most crushed housings that I have seen or heard about have had the slots in the rotor housing. The aluminum rotor housing are lined with steel and this adds to the crushing strength. Then you have the drag racers that are getting up to 400 HP per rotor and not crushing the rotor housing. What I am apprehensive about is the RX8 engine has gone back to rotor housing O-ring slots.
We can also control the diameter of the tension bolts. Higher strength, smaller diameter bolts with a lower tensile spring rate will reduce the compressive load on the rotor housing due to rotor housing expansion. As you may recall we contacted a bolt manufacturers for such bolts a few years ago. Nothing came of it as the shrunk rotor housing phenomena sort of disappeared.
It was thought that grinding fins in the water jacket was also necessary to improve the heat transfer to the coolant. That too has not been done much lately and it appears that that is not necessary. I suspect the original incentive for this practice was the carbon deposits on the rotor housing walls just south of the hump. I also think that those carbon spots had more to do with the break down temp of the oil being used to lube the apex seals. I suspect that has gone away with the use of 2 cycle oil mixed with the fuel and 500 F Mobil One synthetic oil in the sump.
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.