Subject: Major Break through in rotary engine cooling.
From: ACRE
Date: 2/4/2004, 1:27 AM


<< Is the reheat on the cold side of the engine shut off?
 Also at what HP level is that? It is kind of hard to believe that
 a 12A front end housing cracks around the 150 HP per rotor level while
 the 13BREW and 20B are pushing 400 HP per rotor in drag racing. Abel Ibbarra
 told me his biggest problem is with rotor bearings running at 11,000 RPM and
up.
  >>

The power out has nothing at all to do with overheating at the 300 degree
level. There just won't be much HP left to measure at 300. Detonation and then
preignition and then silence.

Lynn E. Hanover


How do you know? Have you ever run an engine on the dyno with 300 F
water temp? Allison ran some engines at 300 degrees F in the early
1930's  and they got plenty of power without detonation. So too did
Continental. The metal temp in the combustion chamber runs 500 F and
is little affected by lowering the water temp from 290 F to 250 F.
See the chart I just uploaded. The HP was not affected at all.

Detonation depends on the charge temperature and not the water temp.
Also it depends on a lot of other things. Mixture for example.
If the charge is cool enough it won't detonate. If you are using an aluminum
intake manifold as I suspect you are  the charge temp will be higher.

Paul Lamar

********************************************************************
In  the  mid-1980s,  Teledyne Continental  Motors  initiated design 
of a 9.O-L, six-cylinder, liquid-cooled aircraft engine, with the 
goals of attaining higher specific output, lower fuel consumption1 
longer periods be- tween engine overhauls, and no weight penalty 
when compared with traditional air-cooled aircraft piston engines. 
Fol- lowing FAA certification in 1988, production of the engine, 
shown in Figure 1, started in 1989.


        To achieve an engine installation weight comparable with 
existing air- cooled aircraft piston engine installa- tions, cooling 
system features include in- creased coolant operating temperatures 
and extensive use of light alloys (in areas such as the cylinder 
head, coolant-pump housing and impeller, radiator, coolant 
circulation piping, and coolant tank). The engine cylinder was 
designed for 121 C  [250 F] maximum engine-coolant inlet temperature. The 
increased operating temperature reduces the heat rejection to the 
coolant (see Pigure 2) and permits a smaller radiator. The smaller 
radiator can also result in reduced aircraft drag. For operating at 
these elevated tempera- tures, higher system pressures were 
specified to suppress boiling and cavita- tion.

        The engine is designed with separate cylinder 
construction~ach cylinder as- sembly consists of a steel cylinder 
barrel and cast-aluminum cylinder head. The barrel and head are 
joined via a threaded joint in each part. The combustion cham- ber 
is formed in the cylinder head. A coolant jacket surrounding the 
combus- tion chamber is cast as an integral part of the cylinder 
head. An ethylene glycoll water mixture circulated through the 
coolant jacket plus oil cooling provides the he~ transfer from the 
combustion section.

        The inlet coolant is directed toward the valve bridge, spark 
plug, and exhaust port areas. The coolant then flows t~ ward the 
lower portion of the cylinder head and exits the outlet port. Oil 
spray from a crankcase-mounted nozzle aimed at the piston underside 
provides addi- tional heat transfer.

        The pump uses a cast-aluminum, closed-impeller design, 
operating at speeds up to 8100 rpm. A pressure rise of 207 kPa at a 
flow rate of 114 L/min. [30 gal/min] oc- curs at rated engine speed.

        The coolant distribution system works in parallel. From the 
coolant- pump exit, the coolant is divided into two branches and 
routed to each bank of three cylinders. It is equally divided among 
the cylinders by an orifice at each cylinder's exit. From each 
cylinder bank, the coolant is collected and routed to a 4.9-L 
coolant tank.

        An existing commercial, ground-ve- hicle ethylene glycol 
formulation was initially selected as the coolant. A 60/40% 
solution of ethylene glycol/distilled water was specified to ensure 
adequate freeze protection. Typical inhibitor pack- ages for these 
coolants include phos- phates, borates, hydroxides, nitrates, sili- 
cates, and triazole. Initial coolant change intervals at 250 h of 
operation or one year were selected, based on coolant supplier 
recommendations.

        To operate at the elevated coolant temperatures, higher 
system pressures are employed for suppression of boiling and 
cavitation. During the engine dyna- mometer development phase, a 
cylinder- head temperature profile was obtained to evaluate 
temperature gradients by em- bedding thermocouples throughout the 
cylinder head. The maximum metal tem- perature measured at the 
combustion chamber surface is 210 C [410 F] between the valves. The typical 
coolant temperature rise across each cylinder is 8-11 C.

Information for this article was provided by J. G. Wheelock, 
Teledyne Continental Motors Aircraft Products, and J. M. Burns, 
Texaco Chemical Company.
 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.