> > > > Ken Welter wrote:
>> > >
>> > > > > Does anyone know of a source for cog belts and pulleys
>>suitable for application to a 13B engine?
>> > > >>
>> > > >> Hank Huddleston LNC 235 Rotary
>> > > >> bahahud@aol.com
>> > > >
>> > > >Ken Welter builds a cog belt reduction drive.
>> > > >Search google for Coot.
>> > > >
>> > > >Paul Lamar
>
>
>> > > I make my pulley as there is no off the shelf source for
>>light weight pulleys.
>> > > I make the small pulley from 1045 steel and the large one from
>> > > 6061-T6 and then hard anodize it.
>> > > What ratio do you need ?I do have some used pulleys that I would
>> > > make a deal on.
>> > >
>> > > Ken
>> > > http://homepage.mac.com/rotarycoot/
>> > > rotary.coot@verizon.net
>> >
>> >
>> > Ken,
>
>> > I'm building a Glass Goose, which will accept a 13B with an
in-line PRSU.
>> > However, the vertical distances are very tight. A lower CG
may be more
>> > appropriate and a higher thrust line might allow a larger
prop -- which is
>> > currently a 65" Warp Drive.
>> >
>> > What size Warp Drive prop are you running?
>> >
>> > Do you have total weights on your PSRU's?
>> >
>> > Thanks,
>> > Scott Gettings
>
>> Ken,
>>
>> Check out Jess Meyers website
http://beltedair.gfwireless.com/default.htm
>> He's not a Rotary powered kinda guy, but he has spent years
>>developing acft belt drives.
>>
>> Jess Meyers built his first Belt Reduction Drive more than
twenty years ago.
>> Since that time, they have been flying proof of the reliability of
>>belt driven aircraft.
>> 67Y now has over 450 hours of trouble free flying. Read about our
>>development.
>>
>> L David Stricker
>> 15054 West Piccadilly Road
>> Goodyear Arizona 85338-8703
>> 602.885.7706
>
>He does not make a ratio suitable for our use. We need something
in the range
>of 2.85:1 up to 3:1. I am very familiar with the history of this airplane
>and I would not exactly call it trouble free flying :) I also
know the test
>pilot :)
>
>Paul Lamar
Its sure been reliable for me as I lost 3 engines in 400 hrs do to
a Ross redrive and have had no problems in 700 hrs on cog belts.
Ken
Ross had a lot of quality control problems towards the end of their life
as a business. There are early ones around still working fine.
Also, I might add, Ken has been in the habit of running NOS though the engine
providing an additional 80-100 HP for water take offs with his 2900
pound gross
Coot.
Paul Lamar
You will like the new coot Paul as it has lots of leg and head room
for your big frame.
I have lifted off at a gross weight of 3100 in the new coot and
that ain't toped out yet.
Ken
As I always say we have just scratched the surface of the capabilities
of the 13B so far.
BTW I was driving in from Las Vegas this morning and I came up with the perfect
solution for the lack of torque in the RX8. Quite simple. Just install an all aluminum
side port three rotor. 50% more torque from the current 160 foot pounds to 240 foot
pounds. If I get to talk to the engineers in Japan next week I am going to
suggest it. After all the competition is using all aluminum 3.5 L and
up piston engines. A 3 rotor would be 3.9 L and have 375 HP with the
same level of tune as the current RX8 2 rotor. The weight would be nearly
the same as the current RX8. That ought to devastate the competition :)
So the 3 rotor RX8 would go 200 MPH so what? :)
Paul Lamar
The AirCraft Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/
Copyright 1998-2003 All world wide rights reserved.