Subject: 13B dynafocal mount - CG issues
From: ACRE
Date: 4/23/2004, 5:12 AM


     > >>>Michael McGee wrote:
     > >>>
     > >>>>Doing some dreaming..
     > >>>>
     > >>>>What do you guys think of the viability of a front cover
cast into the form
     > >>>>of a standard Lycoming dynafocal-1 mount?
     > >>>>
     > >>>>A loose collection of my thoughts so far:
     > >>>>
     > >>>>I think it would sell well enough to get the price under
$500 for the
     > >>>>kit.  I was bs-ing with the local rotary engine builder the
other day and
     > >>>>he showed me a very nice third-gen oil pan that was cast as
a replacement
     > >>>>for the stamped steel original.  The reason behind the pan
is another story
     > >>>>but the casting work looked great (from this engineer/
non-casting expert's
     > >>>>perspective anyway).  He insists that he has a casting guy
that is capable
     > >>>>of making what we need if I can get him a proto type part.

     > The idea behind this is fairly sound since it would eliminate
some of the
     > engineering rotary conversion folks go through. You need to
control the price
     > as much as possible to keep it attractive. Would this be an
addition to a
     > traditional dynafocal mount that basically adapts the Mazda
engine to it, or a
     > dynafocal-like mount with multiple pieces, that could support
either engine?
     > Would your front plate be enough to mount the engine with, or
would we still
     > need to fabricate additional support members to the far side of
the engine?
     >
     > Brock's Lycoming mount for the Cozy is $625. If your item is an
adapter to a
     > dynafocal, it would cost me, as a builder, $1125 for this
combination. The
     > Conversion Concepts mount (if you set aside Paul's issues with
it for the time
     > being) is $1098. That's not unattractive for a mount that does
more (by
     > allowing the use of either engine, making the plane easier to
sell, or making
     > retrofits easier). However, if the cost climbed much above your
estimate or if
     > additional engineering was still required, it would be harder to
compete.
     >
     > With respect to the water pump, should I tease Paul and suggest
an electric
     > water pump? =)
     >
     > How serious are you about creating this? If you started and then
changed your
     > mind after making a few, would you publish the specifications and a
     > dimensional drawing? Knowing that a part will be available when
I'm ready to
     > actually mount the engine is one of the factors a builder has to
consider.
     >
     > Regards,
     > Chad


     Have you considered CG issues???  When I looked at this a couple
of years ago I considered building an engine adapter to fit the standard
conical
     mount (for a RV-4) but determined that the CG of the engine would
be moved forward a significant amount.  I don't remember the exact
amount, but I
     think that it was about 2 inches.

     Ken Powell


Once I get the mockup shaped out of Styrofoam I'll have a better idea of
exactly where the CG will end up.  I'm pretty sure it won't be any worse
than an O-360 with a constant speed prop.

Mike McGee, RV-4 N996RV, O320-E2G, Hillsboro, OR
13B in gestation mode, RD-1C, EC-2


Mike you might want to make it fit the RX8 engine. Here are some pictures
of the RX8 front cover. If you can... move the stock water pump cartridge
down along side the engine instead of up top. This minimizes the bad effects
on the front cover when the engine is run at high speed with low water levels.
More on that later.
It also gives a straight shot into the back side of the pump impeller
improving the pump efficiency..

Paul Lamar

The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.