Subject: P Ports & Jim Mederer is not always right.
From: ACRE
Date: 5/22/2004, 9:04 PM

snips...

Jerry, I find it hard to believe that smaller ports will give you
more
than 240 HP at 6000 RPM that you would get with the monster Leman
ports.  We should dyno two engines back to back to find out for sure.
Notice that the BSFC is lowest on the Leman engine at about 6200 RPM.


Hans "I-can't-believe-I'm-disagreeing-with-Jim-Mederer" Conser


Hans,  the goal is 220 hp  @ 6000 rpm but realistically anything above
200 hp is going to be a success and we can go on from there.  My
throttle body has thick walls intentionally so that the  port can be
easily  enlarged later if we so desire. This not a race engine.   The
PowerSport engine develops 215 hp.  I am willing to bet it has SMALLER
ports than our design.       Jerry


BTW Jim Mederer is not always right. I remember back about 1993 or so Jim
was after
another land speed record with the third gen RX7. He held the previous
record
with Don Sherman driving a second gen at about 238 MPH as I recall. Don
called
me an invited me up to Wendover to have a look at the car. I flew the C182
up
and went out on the salt. The car had 200 pounds of down force at 120 MPH
on the
nose and nothing on the tail. I told Jim that would never work and he was
going
to crash somewhere around 230 MPH. It would spin out so fast no human
could catch it.
The next thing that happened a big thunder storm rolled in over the
mountains to
the North West. The officials came around and had everybody evacuate the
salt
immediately. No time to load everything up on the trucks and trailers.
Some big
high buck Japanese stereo company had this huge electric car with dozens
of lead
acid batteries. When the rains came they flooded the salt to several
inches deep.
The electric car was destroyed by the salt water and most of the other
cars
and vehicles were damaged. Some photographers from Popular Science and Don
Sherman
asked me to fly them over the salt in the C182 to take pictures. One of
the pictures
made the center fold of Pop Science. That was it for that year.

Next year or maybe the next time they ran the speed trials Jim drove the
car
and lost control over 200 mph. Mazda had hired a film company to shoot the
attempt.
You could see the car rapidly car spin around and lift off to an altitude
of about ten
feet. It then did a lomchavack(s?) and would up spinning down the salt
upside down on it
roof at about 200 MPH. Jim was shaken but not seriously hurt. I saw Jim
out at the airport much
later  where he keeps his GlassAir and I told him "I told you so". He said
you are not
always right Paul Lamar:)

Here is a short article I wrote about it back in 1992 along with a QB
program
to calculate what happened and the output from the simulation.

Paul Lamar

Salt Speed by Paul Lamar

A friend of mine recently attempted an assault on his own 240 MPH
land speed record with a 771 horsepower, 3 rotor, 3 turbo charger
Wankel engined  1992 Mazda RX7.

One or two  relative uneventful  runs were made with peak speeds
over  230 MPH. On the third run the car was seen to snap sideways
and instantly  lift off the salt to an altitude of about ten
feet, snap roll and do what is called in aerobatic aircraft
competition, a Lomchavak.  An excellent  film was made  of the
unfortunate event by a Japanese film crew in an ideal position
near the course.

The car finished by spinning down the salt on it's roof.
Fortunately my friend  was shaken but not hurt physically.

Although I had nothing to do with the engineering of the car I
thought it interesting enough to analyze what happened in the
first 90 degrees of the car snapping sideways. This is
accomplished in the following BASIC program. I have not been
involved in race car engineering since 1973 or so. The last 20
years of my life have been spent with computers so I decide to
use the computer to analyze this event.

Back in 1965 while  I was working for Chaparral Race Cars in
Midland Texas and indirectly  for Chevrolet Research and
Development we were using IBM Mainframe computers to model race
cars and analyze the potential lap times.

I published a paper on the Aerodynamics of Group 7 Race Cars in
the proceedings of the American Institute of Aeronautics and
Astronautics in 1968. In this paper I used a mathematical model
of the Group Seven race car of it's aerodynamic characteristics
and it's tires.

At that time it was known by those of us at Chaparral and others
the large role aerodynamic down-force played in the stability and
cornering speed of high speed vehicles.

So it was natural for me to attempt to do a mathematical model of
the 1992 Mazda RX 7 salt racer.

The body of the Mazda RX7 salt racer had only minor
modifications. The internal layout and structure of the car were
entirely different of course. The special 3 rotor engine was set
well back in the chassis to achieve 50 50 weight distribution. A
mistake in engineering in my opinion for reasons explained later. A
belly pan was added underneath the car completely sealing off the
normal radiator cooling air exit. A large transmission tunnel was
fabricated to accommodate the longer engine/large transmission
and duct the cooling air rearward.  An unsuccessful attempt was
made to enhance aerodynamic down force at the rear with an up
sloped underpan.

Several instrumented relatively low speed  runs were made at El
Mirage dry lake in Southern California where lift forces were
measured.  Down force of 200 pound on the nose and zero lift or
modest down force on the tail were estimated by extrapolation to
be available at 200 MPH.

Due to certain stock body rules at the Bonneville meet it was
decided to run the car with this unfortunate configuration. How
unfortunate this configuration really was was not fully
appreciated  at the time by my friend. No effective wing at the
rear was used. The stock rear "spoiler" or vestigial wing was
mounted too close to the body to be effective.

Several aerodynamic engineers have suggested tail fins over the
years as a solution to the vehicle stability problem. These
aerodynamic engineers have been, in general ignorant, of the role
that the tire thrust characteristics play in the stability of a
automotive vehicle.

From Von Doenoff's book "Theory of Wing Sections" the lift
coefficient as a function of the angle of attack is a function of
the aspect ratio. Low aspect ratio wings require high angles of
attack to generate high lift coefficients. As a rough rule of
thumb a wing with a 10 to 1 aspect ration has a max lift
coefficient of around one and that lift coefficient is achieved
around 10 degrees angle of attack.

Since the wing used as a tail fin is oriented vertical on the
rear of the car the yaw angle would have to be 10 degrees to
achieve a lift coefficient of one.  For a typical tail fin with a
aspect ratio of one the angle of attack or yaw angle of the car
would have to be roughly 45 degrees to extract a significant
restoring moment. Let us calculate the restoring moment per degree
of yaw angle of such a tail fin at 200 MPH. Let us say we have
two such tail fins 1 foot high and 1 foot wide. Since the dynamic
pressure at 200 MPH is 100 pounds per square foot we would have
200 pounds of lateral force from the tail fins at a yaw angle of
45 degrees.

At a yaw angle of 1 degree we would have only roughly a
insignificant lateral force of 4.45 pounds.

Now let us calculate the effect of several pounds of down force
on the rear of the same car. Lets us say the coefficient of
friction on the salt is 0.4 and the tire generates its maximum
cornering force at 4 degrees.  Lets also say the car weighs 3200
pounds with 50% of the weight on the rear. At a yaw angle of 4
degrees the rear tires will be generating a lateral force of
1600 pounds times .4 or 640 pounds. At one degree it is roughly
160 pounds. This is 36 times higher than the lateral force
achieved by the tail fins.

Let us say the wheel base is  is eight feet and the 25% cord line
or center of pressure on the tail fins are located 5 feet behind
the CG. The restoring moment from the tail fins is then 5 feet
times 4.4 pounds or 22 foot pounds. Since the tires are located
only 4 feet behind the CG the restoring moment is 160 times 4 or
640 foot pounds.

Now these assumptions so far are based on a no-traction-from-the-
rear-tires condition. Let us assume  that the maximum traction
force from the rear tires is a constant. In other words if we are
using all the available traction to accelerate with we have none
left to provide stability. The equation is MaxTract^2 equals
LatTract^2  plus LongTract^2. You might recognize this equation
from geometry as  r^2 = x^2 + y^2 or the equation of a circle.

Mark Donohue made this relationship famous by calling it the
friction circle.

Rearranging the equation and solving for Lateral Traction we get
LatTract equals the square root of MaxTract^2  minus LongTract^2.

We have already calculated max traction at 160 pounds so 160
squared is 25,600. Let us say we are using 90 percent of the
available traction for acceleration or 144 pound to accelerate
with. 144 pounds squared is 20,736. 25,500 minus 20,736 is 4864
and the square root of that is roughly 70 pounds of lateral
restoring force. This is still 16 times higher than what we can
obtain with the tail fins at one degree.

Let us now assume we have a horizontal wing with a cord of 9
inches and a span of the 60 inches. The wing area is 3.75 square
feet. the aspect ratio will be 6.66 and we are running it at a
negative angle of attack sufficient to generate a down force
coefficient of one. At 200 MPH the dynamic pressure is roughly
100 pounds per square foot or we have 3.75 times 100 pound or 375
pounds of down force.

Max Traction is now 1600 pounds plus 375 pounds equals 1975. 1975
times 0.4 is 790 pounds. Let us say we are using the same throttle
opening we had without the wing to accelerate with or 144 pounds.
Going back to our equation of a circle we have 790 squared
equals 624100 minus 144 squared or  20736 equals 603364. the
square root of that is now 776 pounds of lateral force. the
restoring moment on the car is now roughly 3100 foot pounds.

Foul you say? We now have the drag of the wing to overcome as
WELL as the mass of the car so we now need more traction. OK let
us calculate the drag of the wing. Von Doenoff in his book gives
the equation for the induced drag factor of a wing of any aspect
ration as Cl^2 divide by pi times the aspect ratio. Since the
down force coefficient we are using is 1 and the aspect ration is
6.66 we have an induced drag coef of 3.14 times 6.66 or 20.9.
20.9 divided into 1 is roughly .05. At 200 MPH the drag from the
wing is the drag coef (.05) times the wing area (3.75) times the
dynamic pressure (100) or 18.75 pounds.

So let us add 19 pounds to the traction trust generated and see
how much that reduces our lateral restoring moment. 144 plus 19
is 163 pounds. 624100 minus 26569 equals 597531. The square root
of that is 773 pounds or roughly 3100 foot pounds of restoring
moment around a vertical axis through the CG.

With one feel swoop we have increased the stability of the car
and made more potential traction available for accelerating.

So you can see you are wasting your time using tail fins.


This article takes and approach to the mathematical analysis of a
complicated subject by using the personal computer in lieu of
differential equations and other higher math techniques. The
personal computer is ideal for doing an enormous number of
repetitive calculations. The benefits of this approach are many.
First of all it is much easier to understand.

Another benefit is an automatic plotting of mathematical
relationships  by merely inputting the output data from this program
into a spreadsheet program such as Lotus 123 and allowing it to
plot the data. You will soon see what I am describing.

Surprisingly the automobile is a much more complicated dynamic
system than an airplane. It has both a road interface and an
aerodynamic interface while the airplane has only the air to deal
with.

Good tire data is hard to come by so we will make a few
assumptions along those lines. One is that the cornering force, up
to about a slip angle of about 4 degrees, is is directly
proportional to slip angle and to the load on the tire. For
pavement this is not true. The coefficient of friction is reduced
with load but for this analysis we are dealing with a road
surface of hard moist salt. The coefficient of friction of the
salt is assumed to be 0.4 however it can vary with the condition
of the salt from year to year.

Side force drag coeff = .7

Dynamic pressure at 200 MPH = 100 pounds per square foot

Car is on the average 3 feet high and 12 feet long or 36 square feet
side area.

Side area = 3 * 12  = 36 * 100 * .7 = 2520 pounds

The CP starts out roughly 1 foot in front of the CG.

The C.P. moves rearward as the car rotates to a 90 angle relative
to the direction of motion.
A similar CP movement occurs with wings when the flaps are lowered or when
the wing stalls.

The C.P. in fact may move behind the CG because of the set back
passenger compartment creating a stabilizing moment.

The following algorithm is used to estimate this situation.
The CP starts one foot in front of the CG and ends up 1 foot behind
the CG when the car becomes 90 to the relative wind.
At a yaw angle of 45 degrees the CP is at the CG.


AeroMomArm = (45 - yawangle) / 45
IF yawangle > 45 THEN AeroMomArm = -((yawangle - 45) / 90)

In any event the aero side force is minor relative to the destabilizing
force from the front tires. It has Little effect on the yaw velocity
achieved. This is true even though the coefficient of friction on
the salt is 0.4 or less.

This analysis ignores the decrease in velocity the car will experience
from the large side forces from both the tires and the increased
aerodynamic
drag. This is justified as the spin to 90 deg requires less than .4
seconds.
At this yaw angle the car will levitate from the surface of the salt
because of a huge lifting force.

The program is written in QuickBASIC 4.5 however it will work
with whatever version of QuickBASIC you might have. QuickBASIC
came with all versions of DOS beyond 5.0.

Initial conditions. You may change these of course to meet your
needs.


thrust =  640         'Thrust from rear tires due to throttle opening.
                      'This amount of thrust is = to 342 HP at 200 MPH
PA = 60               'plan form area of the car looking down on it.
LCf = .6              'lift coeff of the car moving sideways
Wt = 3200             'Car total weight
FDF = 200             'front down force at 200 MPH
RDF = 0               'Rear down force at 200 MPH
SteerAngle = 1        'initial steer angle at the tires input by the
driver.
k2 = 1360             'Rotational inertia of the car
k1 = .1               'Tire cornering coeff per degree or cornering
stiffness
                      'up to 4 degrees on salt.
MaxSideForce = 2520   'Pounds of aero side force

CLS

PRINT
PRINT
PRINT "               SALT SPIN2 Copyright Paul Lamar 1992 "
PRINT "                         (310) 374 1673  "
PRINT
PRINT
PRINT

INPUT " Press any key to start "; z$
CLS


date1$ = MID$(DATE$, 1, 2)
date2$ = MID$(DATE$, 4, 2)
date3$ = MID$(DATE$, 9, 2)
time1$ = MID$(TIME$, 1, 2)
time2$ = MID$(TIME$, 4, 2)

filename$ = time1$ + time2$ + date1$ + date2$ + "." + date3$


OPEN filename$ FOR OUTPUT AS #1

PRINT #1, "Time  FCF    RCF  Torque   Y.Acc   Y.Vel   Y.Ang   Aero Mom
Lift   Net Wt"
PRINT #1, "Sec   Lbs    Lbs  Ft Lbs   D/S^2   Deg/S   Deg     Ft Lbs
Lbs    Lbs"
PRINT #1,

FOR Ti = 0 TO 1 STEP .01            'Time and time increment


PRINT #1, USING "#.##"; Ti;

steerangle = steerangle + yawangle

fcf = k1 * steerangle

IF steerangle > 4 THEN fcf = .4   'tire cornering force is limited after 4
deg

frontdf = COS(yawangle / 57.295) * FDF

fcornforce = fcf * ((Wt / 2) + frontdf - (lift / 2))

IF fcornforce <= 0 THEN fcornforce = 0

PRINT #1, "  ";              'front tire cornering force
PRINT #1, USING "####"; fcornforce;


rcf = k1 * yawangle

IF yawangle > 4 THEN rcf = .4

reardf = COS(yawangle / 57.295) * RDF

c1 = (rcf * ((Wt / 2) + reardf - (lift / 2)))

IF c1 <= thrust THEN GOTO skipit

rcornforce = SQR(c1 ^ 2 - thrust ^ 2)

GOTO skipit2

skipit:
rcornforce = 0

skipit2:

PRINT #1, "  ";
PRINT #1, USING "####"; rcornforce;

Tor = (fcornforce * 4) + aeromoment - (rcornforce * 4)

'Total moment from front tires + aeromoment

PRINT #1, "  ";            'total yawing torque on car
PRINT #1, USING "#####"; Tor;

alpha = (Tor / k2) * 57.295      'k2 is polar moment of inertia

PRINT #1, "   ";              'Yaw accleration
PRINT #1, USING "####"; alpha;

yawvel = yawvel + alpha * Ti

PRINT #1, "     ";
PRINT #1, USING "####"; yawvel;

yawangle = yawangle + (yawvel * .01)

PRINT #1, "     ";
PRINT #1, USING "##.#"; yawangle;

IF yawangle > 90 THEN GOTO endit

AeroMomArm = (45 - yawangle) / 45

IF yawangle > 45 THEN AeroMomArm = -((yawangle - 45) / 90)

AeroSideforce = SIN(yawangle / 57.295) * maxsideforce

aeromoment = AeroSideforce * AeroMomArm

PRINT #1, "   ";

PRINT #1, USING "#####"; aeromoment;

lift = ((LCf * PA * 100) * SIN(yawangle / 57.295)) - frontdf - reardf

PRINT #1, "     ";
PRINT #1, USING "#####"; lift;



wtoncar = Wt - lift
IF wtoncar < 0 THEN GOTO endit
PRINT #1, "     ";
PRINT #1, USING "####"; wtoncar
NEXT


endit:
PRINT #1,
CLOSE #1
CLS
out$ = "more<" + filename$
SHELL out$
END


----------------------------------------------------------------------------
----

Thrust  0     Cornering Force 640
Thrust  25    Cornering Force 640
Thrust  50    Cornering Force 638
Thrust  75    Cornering Force 636
Thrust  100   Cornering Force 632
Thrust  125   Cornering Force 628
Thrust  150   Cornering Force 622
Thrust  175   Cornering Force 616
Thrust  200   Cornering Force 608
Thrust  225   Cornering Force 599
Thrust  250   Cornering Force 589
Thrust  275   Cornering Force 578
Thrust  300   Cornering Force 565
Thrust  325   Cornering Force 551
Thrust  350   Cornering Force 536
Thrust  375   Cornering Force 519
Thrust  400   Cornering Force 500
Thrust  425   Cornering Force 479
Thrust  450   Cornering Force 455
Thrust  475   Cornering Force 429
Thrust  500   Cornering Force 399
Thrust  525   Cornering Force 366
Thrust  550   Cornering Force 327
Thrust  575   Cornering Force 281
Thrust  600   Cornering Force 223


----------------------------------------------------------------------------
----

Time  FCF    RCF  Torque   Y.Acc   Y.Vel   Y.Ang   Aero Mom   Lift   Net
Wt
Sec   Lbs    Lbs  Ft Lbs   D/S^2   Deg/S   Deg     Ft Lbs     Lbs    Lbs

0.00   180     0    720     30        0      0.0       0      -200
3400
0.01   190     0    760     32        0      0.0       0      -200
3400
0.02   191     0    763     32        1      0.0       1      -199
3399
0.03   193     0    773     33        2      0.0       1      -198
3398
0.04   199     0    798     34        3      0.1       3      -196
3396
0.05   211     0    848     36        5      0.1       5      -193
3393
0.06   233     0    937     39        7      0.2       8      -188
3388
0.07   269     0   1084     46       11      0.3      13      -181
3381
0.08   324     0   1310     55       15      0.4      19      -172
3372
0.09   408     0   1651     70       21      0.7      29      -159
3359
0.10   530     0   2150     91       30      1.0      41      -139
3339
0.11   708     0   2873    121       44      1.4      60      -112
3312
0.12   742     0   3029    128       59      2.0      84       -75
3275
0.13   735     0   3023    127       76      2.7     113       -27
3227
0.14   725     0   3015    127       93      3.7     149        31
3169
0.15   714     0   3003    127      112      4.8     188       102
3098
0.16   699     0   2986    126      132      6.1     232       185
3015
0.17   683     0   2963    125      154      7.7     279       281
2919
0.18   663     0   2931    123      176      9.4     326       391
2809
0.19   641     0   2889    122      199     11.4     372       515
2685
0.20   615     0   2834    119      223     13.6     414       653
2547
0.21   587     0   2763    116      247     16.1     449       805
2395
0.22   556     0   2672    113      272     18.8     473       970
2230
0.23   522     0   2560    108      297     21.8     482      1148
2052
0.24   485     0   2421    102      321     25.0     473      1337
1863
0.25   445     0   2254     95      345     28.5     441      1535
1665
0.26   403     0   2055     87      368     32.1     383      1740
1460
0.27   360     0   1822     77      388     36.0     295      1948
1252
0.28   315     0   1556     66      407     40.1     177      2157
1043
0.29   270     0   1256     53      422     44.3      27      2362
838
0.30   225     0    926     39      434     48.7     -77      2560
640
0.31   181     0    647     27      442     53.1    -181      2746
454
0.32   139     0    375     16      447     57.5    -297      2918
282
0.33    99     0    101      4      449     62.0    -421      3072
128
0.34    63     0   -169     -7      446     66.5    -552      3208


Kevin & Kim wrote:

Got a copy of that centerfold picture?

I think I threw that issue of Pop Sci out. Could be around December 1991.

I'll ask Don Sherman He may have a copy or know what month it was.

Paul Lamar
 
The AirCraft Rotary Engine NewsLetter.  Powered by Linux.
ACRE NL web site. http://home.earthlink.net/~rotaryeng/            
Copyright 1998-2003 All world wide rights reserved.